dealdd

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 67 total)
1 2 3 4 5
  • Author
    Posts
  • January 8, 2011 at 8:12 am in reply to: tumble dryers out side #340461
    dealdd
    Participant

    Re: tumble dryers out side

    ok cheers lads will bear it in mind for futer.

    January 7, 2011 at 6:19 pm in reply to: tumble dryers out side #340459
    dealdd
    Participant

    Re: tumble dryers out side

    yeh all the ones i have worked on with this fault have ntc’s in suppose the only way to prove it is to heat sensor up with hair dryer and then test dryer out??
    is there any way of finding out running temps of these dryers with ntc’s in or are they all different??

    January 5, 2011 at 3:46 pm in reply to: cda ci993 w/d #340191
    dealdd
    Participant

    Re: cda ci993 w/d

    ok cheers sound like fun. these machines are apain in the ar**

    September 27, 2010 at 11:21 am in reply to: hoover oph714d/1-80 #331256
    dealdd
    Participant

    Re: hoover oph714d/1-80

    yes this is the part number HVR49015449

    August 12, 2010 at 8:51 am in reply to: zannusi zwf12211 #327461
    dealdd
    Participant

    Re: zannusi zwf12211

    have already done that taco and magnet was nice and tight

    August 11, 2010 at 3:45 pm in reply to: zannusi zwf12211 #327459
    dealdd
    Participant

    Re: zannusi zwf12211

    yeh pulled plug in an out a couple of times and measured again all ok

    August 10, 2010 at 2:29 pm in reply to: indesit wd11uk #327227
    dealdd
    Participant

    Re: indesit wd11uk

    went back to this today. found a small splash of solder on the pcb. removed it and all worked fine.

    June 7, 2010 at 9:24 am in reply to: stoves thermostat conversion kit #321619
    dealdd
    Participant

    Re: stoves thermostat conversion kit

    can you send to grant.jane@hotmail.com as i have not recived many thanks

    June 1, 2010 at 9:21 am in reply to: miele d/w g694sc #321276
    dealdd
    Participant

    Re: miele d/w g694sc

    checked all the obvious and can see anything. has any one got some paper work on these machines before i go back.

    April 15, 2010 at 3:05 pm in reply to: aeg d/w #317877
    dealdd
    Participant

    Re: aeg d/w

    how much of a gap should be at each end i would have thought they should be right to the hinges to stop splashing over the edge

    April 6, 2010 at 12:34 pm in reply to: hoover wdm120 #316963
    dealdd
    Participant

    Re: hoover wdm120

    no tested for that i have had one of them before

    February 3, 2010 at 9:01 am in reply to: whirlpool side by side f/f #310631
    dealdd
    Participant

    Re: whirlpool side by side f/f

    has any one got service manual for these or a circuit diagrame. they are usually on back of these but this one is missing

    January 25, 2010 at 10:17 am in reply to: beko fridge freezer american style ap930x #308145
    dealdd
    Participant

    Re: beko fridge freezer american style ap930x

    yeh no prob but need e-mail address

    January 22, 2010 at 10:33 am in reply to: beko fridge freezer american style ap930x #308142
    dealdd
    Participant

    Re: beko fridge freezer american style ap930x

    thought it was strange that the fridge still got cold with a broken fan. i found that only the salad bins were freezing stuff and the vent in the bottom was covered in ice. i will send you all the info i have on these units. whats your email address

    January 21, 2010 at 10:57 am in reply to: beko fridge freezer american style ap930x #308140
    dealdd
    Participant

    Re: beko fridge freezer american style ap930x

    yes fan in freezer behind ice maker. back panel is a pain to get of as held in with pastic clips

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 67 total)
1 2 3 4 5