Dragan

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 64 total)
1 2 3 4 5
  • Author
    Posts
  • October 24, 2012 at 5:27 pm in reply to: Indesit washer/dryer WIDXL 126SUK “Flashing Lights” #383545
    Dragan
    Participant

    Re: Indesit washer/dryer WIDXL 126SUK "Flashing Lights"

    I have sent you pm.
    Good lack!

    Dragan

    October 16, 2012 at 3:36 pm in reply to: Elektrabregenz WA 714 #382961
    Dragan
    Participant

    Re: Elektrabregenz WA 714

    I am not sure-should be made by Brandt

    October 9, 2012 at 11:05 am in reply to: RSH5PTTS1/XEG #382609
    Dragan
    Participant

    Re: RSH5PTTS1/XEG

    Thank you,
    Dave

    September 26, 2012 at 4:45 pm in reply to: whirlpool washer/dryer awz510e #381730
    Dragan
    Participant

    Re: whirlpool washer/dryer awz510e

    Hi,
    You have to replace program selector.Order code
    4812 273 28282.


    Dragan

    September 26, 2012 at 4:30 pm in reply to: whirlpool adg 7540 dishwasher #381820
    Dragan
    Participant

    Re: whirlpool adg 7540 dishwasher

    Hello,
    do You know 12NC /service/ number?


    Dragan

    September 26, 2012 at 4:23 pm in reply to: Zanussi ZWD14581W1 fault code E9F #381884
    Dragan
    Participant

    Re: Zanussi ZWD14581W1 fault code E9F

    Hello,
    E9F means communication error between PCB and Inverter,
    Check wiring,PCB and inverter.

    Dragan

    September 24, 2012 at 5:40 pm in reply to: Candy Tumble Dryer Water Container #381727
    Dragan
    Participant

    Re: Candy Tumble Dryer Water Container

    Water level is detected by the pressure switch.

    Dragan

    September 24, 2012 at 5:27 pm in reply to: Candy f/freezer CPCA240FFK #381713
    Dragan
    Participant

    Re: Candy f/freezer CPCA240FFK

    I have writen in English trying to help You.I am not able to translate English to English.Some dictionary could help,perhaps.

    Dragan

    September 24, 2012 at 5:19 pm in reply to: Bosch F/F KGN36 Evap removal #381699
    Dragan
    Participant

    Re: Bosch F/F KGN36 Evap removal

    Have You received my private message?

    Dragan

    September 24, 2012 at 4:58 pm in reply to: Hoover HOD6615 Dishwasher no heat #381653
    Dragan
    Participant

    Re: Hoover HOD6615 Dishwasher no heat

    Hi Johnnyj,
    it is possible to check pressure switch.Disconnect wires and connect the other ones connected with Your ohmmeter.Start the machine and wait for spray pump start.If You read 0 ohms- pressure switch is OK.
    Also,You shold check wires continuity from PCB and door MS to heater and pressure switch.Heater releay on PCB,too.

    Dragan

    September 24, 2012 at 4:17 pm in reply to: Candy f/freezer CPCA240FFK #381711
    Dragan
    Participant

    Re: Candy f/freezer CPCA240FFK

    Hi Rob,
    when in doubt,carry out the autotest at first.

    Dragan

    January 4, 2007 at 6:40 pm in reply to: Indesit WI 101, 6 flashes? #199483
    Dragan
    Participant

    Re: Indesit WI 101, 6 flashes?

    Hi,
    you should check selector and connectors that belong to it.Selector motor,too.

    Regards,Dragan

    January 4, 2007 at 6:33 pm in reply to: gorenje tumble dryer #199499
    Dragan
    Participant

    Re: gorenje tumble dryer

    Hi,
    you have to gain access from the front side.In there is a wheel that you must take out to make space to put belt through.

    Regards,Dragan

    December 24, 2006 at 3:37 pm in reply to: Whirlpool AWG 450 D/W Error Code #198696
    Dragan
    Participant

    Re: Whirlpool AWG 450 D/W Error Code

    Hi,Fairdeal

    you can find error codes for ADG 450 in “Known Error Codes”
    page 5.

    Dragan

    December 24, 2006 at 3:33 pm in reply to: **KNOWN ERROR CODES** #103906
    Dragan
    Participant

    Re: Known Error Codes

    Whirpool ADG 450/03 Dishwasher

    ALARMS:


    ALARM LED flashing
    E1 L1 The anti-flooding
    system has tripped
    E3 L1+L2 No hetaing the water
    E4 L3 Temperature sensor
    failed
    E5 L1+L3 Unable to fill the water
    E6 L2+L3 Unable to drain
    E7 L1+L2+L3 Turbine flow
    regulator malfunction
    E9 L1+L4 Tank fill limit
    exceeded
    LED L5 is always ON
    L1-the first LED from left ,L2-the second etc.

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 64 total)
1 2 3 4 5