[edthespiv]

Re: Leisure CM10FRC (range cooker)

to remove top to gain access to facia. remove 2 screws on r/h on top then remove 2 screws from rear holding top on. then slide to right. To remove l/h side remove 4 screw from top then lift off. this will enable you to remove screws to facia

[edthespiv]

Re: Servis

i had this if the machine is dead no power.
i spoke to an engineer who did contract work for servis.He told me to repair R1 or R2 on the control panel.It worked for me

[edthespiv]

Re: credaplan continental part no

thanks steve for your help. i see what you mean about the tags which i will replace with new ones

[edthespiv]

Re: indesit wia111 only fills

thanks for your help i will walk away with the call charge

[edthespiv]

Re: Hotpoint WMA Washer draining problem

i once had this problem. the customer had used a “colour run” sheet which was like “bounce” sheet used in T/D’s. It was floating around in the drum.

[edthespiv]

Re: Fitting a new support tube on Hotpoint twin tub

make sure you clean sharft and lightly grease as new black plastic tube can be difficult to fit. Also when fitting clamp (keyring style) thread a piece of string through first part of clamp then run string down over seal this is much easier than using screwdriver to locate clamp……hope this helps and dont forget to swear at it as it will make the job easy

[edthespiv]

Re: bosch hbn9163gb/02 hinges

Penguin45 wrote:096784?

Chris.

i have looked at 096784 and they look completely different shape where you connect the door to the oven the ones i am using 491777 look the same.
If i fit 096784 will they fit in the hinge giudes?

[edthespiv]

Re: indesit widl f 03

went back yesterday, took a ntc out of a wma heater cut the wire to old connector block and fitted new tags works all ok……..Thanks for your help………kind regards………..Andy

[edthespiv]

Re: indesit wdg1095 no pump

thanks chris, sometimes you need someone to just confirm what i thought as it was w/d and an indesit it might be wired different. cheers

[edthespiv]

Re: indesit widl f 03

this machine pumps and fills at tha same time then f03 fault appears. Can this be a fault with the heater themistor…..

[edthespiv]

Re: Bosch WTL6103GB – Condenser Drier – pump problem

hi mick
i went to a bosch condenser the other week. to check pump take side panel off, the spring is easy to take off with pliers.on cover over housing is a screww remove this and pump located underneath.clean out fluff.
Beware the out come of my repair ended up was the fan picked up the water then flicked it onto the heater then took the control board out. javascript:emoticon(‘:cry:’)
Crying or Very sad ouch!!

good luck

Andy

[edthespiv]

Re: tricity bendix fault flahes

dear Chris

ive been a complete “Rodney” a plonker.
ive changed my email new one andyinpego@hotmail.com.
could you please resend info

Kind regards………………..Andy

[edthespiv]

thanks toni
great site, at least i will be able to ask for the right part in spainish. so out the window goes shouting slowly in english at the person like us brits do when abroad.

cheers mate……..regards…………andy

[edthespiv]

Martin wrote:

edthespiv wrote:
does anyone know of wholesalers that would be able to supply me with spares in Spain?

hay muchos suministradores en España (there are many wholesalers in spain) usted debe aprender a hablar español primero aunque (you must learn to speak Spanish first though) cuando mayoristas no hablan inglés (as wholesalers do not speak or understand English!

¡Mejor de suerte!
😀

my first bit of spainish here go’s

soy reparo lavadoras.

how i’m i doing…..i feel i have some way to go

[Author]

Posts