Forum Replies Created
-
Posts
-
Re: ACM804/BK Whirlpool Induction Hob
sound like it. i have a £30 one from lidl it turn off if i lift the pan and to be fair thay have to assume people will lift the pan off
Dave
the only long shot in this is are all you supply joints tight as i am not sure what an arcing joint would do to the mosfets in the boards
Dave
Re: HELP with Hotpoint WDL540P & Indesit WIXXE167 interlock
does it with a lot of machines went to a Beko earlier no start. switched off, reached underneath, gave brushes a wack with a screwdriver, turned on and away it went. diagnosis proved so changed brushes got paid and left
Dave
Re: HELP with Hotpoint WDL540P & Indesit WIXXE167 interlock
miss the P off (its only colour) and you get both
on a lot of machines these days if the brushes are open circuit it wont start
Dave
Re: HELP with Hotpoint WDL540P & Indesit WIXXE167 interlock
lock connection fairly straight forwards. they have reversed connector but the numbers are the same ( 2,3 and 4 ) if old matches new all ok)
i am confused about the second one as you seem to have replaced a solenoid lock with a non solenoid one interlock should be int102 if it clicks as the 51 lock does not click
plus did you look at brushes ?
Dave
Re: aeg 16850 e20 – and rumbling noise on dry cycle
ventilator for your comes as part number 1323243442
you can check if i am right
remove lid
ventilator unit is in the rear right
remove belt
spin fan unit if it rumbles you have found italso this is the only mechanical device that is only used by the tumble dryer. if it was the pump or the motor it would do it on wash as well
Dave
Re: Beko WME7247 not heating
its one of those questions that you cant answer until you know the fault and the area you live because lab prices vary across the country
the only way you are going to get an estimate is to ring a local engineer and get a cost based on what you think it is. Then if you like the price you will have to pay him to come out and give you an accurate one
Dave
Re: ACM804/BK Whirlpool Induction Hob
since these hobs are designed to replace all and any other hob i cannot see your installation has anything to do with it
Dave
Re: leaking fluff filter
your Enr is not complete so cant know the prt no for certain but
for early model there is 1 but for later ones there are 2 types
go here
http://www.bosch-home.co.uk/store/spareparts/searchput you full Enr in
Dave
Re: Hotpoint ST98 oven not heating up
i dont know the oven but if its a simple timer you can short it out electrically. if thr timer also controls oven temp then you have no choice but to replace
post a photo of the back of the timer and most enginners will know if it can be bridged
Dave
Re: Smeg SUK81MX: Oven not working
that thermostat may have been to bring the cooling fan on when things get hot. did you happen to notice if the fan was running when you shorted it
Dave
Re: Howdens HJA8630 dishwasher – all programme lights on
this unit is built by Beko
will be the main board in the door available in the site shop
http://shop.ukwhitegoods.co.uk/catalogs … 1899450650
from what i can see this should be the correct board
but
you have to understand that if if it does not cure the problem you will not be able to return the board but if it does you will have a big smile on your face
its fairly cheap so woth a shotDave
Re: Creda synergie element required please
most common creda element is
http://shop.ukwhitegoods.co.uk/catalogs … /?q=233920
its quite different from most elements such as single screw fixing so if it looks right it should fit
Dave
Re: Smeg SUK81MX: Oven not working
can only find SUK81MFX as the closest model
this is the switch that should fot yours
http://www.servevastdirect.co.uk/index. … ct_id=1319
but i would ring servast and check. this is behind the knob you turn to select the elements. it has a number of contacts and the fail often. if you look at it you may be able to see melted terminals
Dave
