Forum Replies Created
-
Posts
-
Re: wf620 rear tub
most black pulleys are 30mm but its not set in stone
remove the pulley and look at rear bearing
30 mm kit uses 6205
35 mm kit uses 6206hope it helps
Dave
Re: Hotpoint washing machine HVL241 filling abnormally
does it fill as soon as the door locks and does not stop ?
if so check the traic on the board that controls the valve
Dave
Re: CDA WC130 8545 495 15840 no circulation
yes normal 40w or so lamp. any size will do but not too small and not energy saving
you need to replace heater element with something that wont affect the board and you can tell if the heater is switched on
lamp has no earth so cant affect the electronicsDave
Re: CDA WC130 dishwasher – Whirlpool made
some electronics a upset by earth leakage on heater
suggestion disconnect heater and connect a 40w lamp to the wires and run dishwasher
if it works you can says its the heater if not then it cant be
Dave
Re: CDA WC130 8545 495 15840 no circulation
to be honest my next step would be to double check QER
trace motor wires back to board
open board and find out if its fad with a relay or a triacif its a relay look at rated voltage and check to see if its energized at any time ( means running unit with board on show)
what you are looking for is 1 of 2 things1 relay is energised with a much lower voltage ie 12v relay gets 6v
2 relay has full voltage but does not close contactno2 is a failed relay no1 is a power supply problem
if its triac operated check the power supply to the board. A lot of dishwasher use series capacitor power supply when they fail it lowers voltage to board and causes fault 1 above
Dave
Re: CDA WC130 8545 495 15840 no circulation
dont know the wash motor readings but sounds about right. i assume qer would check power supply caps on the board so that should be ok.
where is the board on your model as i dont know it well. is it in door or at the front clipped to the chassis. if its down below had one with a similar fault years ago and it was the lead from the pressure switch. not broken but must have had a short on it but i could not find it. all i know was when i stuck my multimeter to earth while it was on the motor started. very weird but a new cable cured itDave
Re: CDA WC130 8545 495 15840 no circulation
so is your got the same faults as mike? or does it present slightly differently.
when you said you had the board looked at do the test it fully or is it just a visual check?Dave
Re: Miele drier intermittent heat
most miele td have a seperate relay board and these fail or go intermittant
relays are cheap enough if you want to solder them to the board
Dave
Re: CDA WC130 8545 495 15840 no circulation
cant find pictures i need to sort out which unit it is but
trace wire back to pcb
check for broken wires if timer is in door
trace wires onto timer is motor relay operated or triac. if relay is it faulty if triac does it look ok ie not got a hole in it
look at timer board find power supply. if it is capacitor fed could be this. you can check this by measuring dc voltage on board. there must be at least 1 relay on the board. if you look at the voltage of this it will give you the line voltage of the board. if when you measure you get a lot less then thats itif you post picture of board will look at it for you
Dave
Re: SMEG selector switches HELP!!!!
ring servast they will give you the part number of the other switch. not everything is on their website and i ring them often
Dave
Re: Bosch island hood DIE975AGB/03
https://portal.bsh-partner.com/TCcustom … dmdb—vm2
this is a die995f/03its very similar may help
dave
Re: Whirlpool Dishwasher top spray arm
does not help pressure but it give the water jets something to push on
Dave
