[electrofix]

Re: EMW issues

cant fault you Tony excellent service with great feedback but as with us all you cant fix everything

regards

Dave

[electrofix]

Re: WMA 31 bearings and spider

when the seal is all the way home it does no go flush
the metal lip of the seal housing sticks up about a mm

i can sometimes get the bolts out of the spider using a blowtorch but most of the time a drill is the only way

as for the 30mm units with no spider being available i have to warn the customer it may be scrap as having to convert to 35mm cost too much

hope this helps

Dave

[electrofix]

Re: Panasonic NNA755W microwave fault

because of the high voltages involved it is not a job to be undertaken by untrained person. there can be enough voltage to knock you across the room after the unit is switched off

the job can be undertaken in your own home or at a workshop. we are in merseyside but there will be other technicians around the country who may be able to quote

look in repairs@ to see if anyone else covers you part of the country

Dave

[electrofix]

Re: Panasonic NNA755W microwave fault

both of these microwaves will probably say invertor on the front

the electronics inside the machine switches the unit off if the microwave hass not started so your problem is in the invertor section of the machine

this is not a home repair due to 5000 volts at the magnetron. it is likely to cost over £100 to put right but you may find a dealer with secondhand spares

Dave

[electrofix]

Re: Tricity /Bendix sie532bu

not seen ccoker so cant tell you how to fit but part number of grill is

3114757002 fast grill unit

according to lux disk

is the other element listed 3110267006 which is lower element in grill cavity

hope this helps

Dave

[electrofix]

Re: Valor EVSF19

try to find your local

http://www.partscenter.co.uk/

or start at

http://www.valor.co.uk

and dig around

Dave

[electrofix]

Re: Sheffield 110

may have to modify one

cant get at Qualtex website but rangemaster element is as follows

ele2056

overall lenth 230mm
internal diameter 180 mm
plate lenth 70mm and width 21
dont know wattage with website down
terminals 24 mm apart

dont know your situation but you may be able to drill a hole in the middle if the term will fit back of cooker

will try to look again but as per normal qualtex website is down on a sat. if it is maintenance a bit of warning would be nice

Dave

[electrofix]

Re: HOTPOINT FDW20

your idea of luke warm and the customers may differ machine may be plumbed to hot water

what i am saying is you need to check heater and if ok check programmer where it connects for bad joints etc. if ok check if heater ever comes on. ie look for the simple things first

hope this helps

Dave

[electrofix]

Re: Hoover Soft Wave Timer Knob

did a google search

http://www.electricalsales.co.uk/produc … p?id=13693

worth a ring

Dave

[electrofix]

Re: Sheffield 110

have you got dimenions

Dave

[electrofix]

Re: lg wm1480fhd

unfortunatly bearing behind seal can be lifted in and out with 1 finger and there is 0.5mm of play so sleeve is damaged.
dont know how this has happened. Did not even know machine had a bearing prob till it started to spin. it was ok on wash and very high spin but made a noise on the way up. its a nice machine works well and is a shame to scrap it but at over £90 for parts its a bit silly. what i need is a scrap machine with other faults and make 1 good one

Dave

[electrofix]

Re: BEKO CDA659FS

bet you were happy when you found that one lol

[electrofix]

Re: BEKO CDA659FS

can send you wiring info etc if you want

Dave

[electrofix]

Re: AEG F3A dishwasher stopping

if you send me your email will send you the manuals later on today or tomorrow if this helps

Dave

[electrofix]

Re: Electric hob

correct 7 inch rings are designed for a seven inch hole therefore they are only 6.5 inch so element does not toch casing

Dave

[Author]

Posts