[fasetester]

Re: creda w22ovw

hi martin and guys went to look at it today the belt had come off because the bearings were shot the were rattling like stones in a cement mixer the lady said she would go for new machine fasetester 🙂

[fasetester]

thanks mick if there was an earth fault would the machine not trip out the circuit breaker what would be the most likely thng to cause a leakage heater or motor ect thanks comptonappliances how do test the ntc and where is it situated on this machine thanks for all your replys

[fasetester]

Re: zanussi fls 1183w

thanks rouge element is that the clip that holds magnet on the shaft of the motor do the come loose would that cause it to skip right to the end of the program just filling breifly then pumping then spinning breifly as if the whol program is speeded up and stopping at the end .fasetester 😕

[fasetester]

Re: zanussi fls 1183w

thanks martin would that be the pump and filter blocked nothing else can the manofold be cleaned by removing the hoses or does the whole unit have to be removed with the filter houseing and pump fasetester

[fasetester]

do you mean the load has caused this oob would it not have kept going and when the load had leveled out then spun fasetester

[fasetester]

Re: creda w22ovw

dont know guys she just said when the wash was finished the clothes were wet is the motor in this machine in the top or bottom and when she tryed to spin them no go she said it was making some kind of noise but not spinning unless the belt has come off or broke and the noise she heard is the motor no unusal faults or thing to look out for fasetester 🙂

[fasetester]

Re: creda ripping clothes

thanks steve problum was a brooch inside door seal and and the pump filter was blocked with a lump of tea towel and a sock up behind heater the machine is a creda excel 1200 model w220vw fasetester 🙂

[fasetester]

Re: creda ripping clothes

thanks iadom and john i know the model number would have helped all i know its a creda simplicty and i think when i replaced the door seal it was a over sized one and the wire band that went around the seal went into a plate with metal teeth like a rachet dont know if that will trow any more light on the subject or not fasetester 🙂

[fasetester]

Re: creda ripping clothes

hi iadom i dont have the model number what is the most likely cause something catching in the drum or over loading thanks fasetester 🙂

[fasetester]

no problem guys first i turned off the power then i cleaned out the sump and cleaned under the little black flap turned off the water supply disconnected the the hose to release the pressure reconnected the hose turned down the water pressure going to the valve turned on the power run a program and it worked ok the customer was happy to hear it wash and that was that thanks all for the help another one for uk whitegoods fasetester 🙂

[fasetester]

sorry to get your beard in a blaze pen i have sorted the the dishwasher no call to lose your temper old man relax chill out fasetester and thank again for all your input. 😉

[fasetester]

wel guys has any one any thing to add about the smeg dishwasher or turning down the water pressure thanks fasetester 🙂

[fasetester]

woopps i nearly for got thanks k for the mail i though it was in my pm box but i tracked it down fasetester 😳

[fasetester]

thanks eastmark for your reply so the smeg can fill and empy for 2 to 3 minutes before starting a programe so you have to wait before deciding if there is a fault should the householder not know that who is using the machine should the meetering tank when it is filling send some water up a channel like a blow off then like spit some water out of it and go down another channel the only way i could get it to work was cut back on the mains pressure so that it would fill and carry on the program the woman said it had not worked like that for a good while it would start and after a while stop and beep after i cleaned out under the black flap and checked the meetering tank for flow even when i removed the main hose to the meetering tank and let it flow into a basin the valve would activate and then stop after a min or so what is your thoughts on turning down the water pressure eastmark thank fasetester 😕 😳

[fasetester]

thanks lawrence for your reply where is the none return flap in the smeg even when i removed the main feed hose from the metering tank and put it in a dish the water would flow for a short time and then stop as i said it would run ok with the pressure turned down is it ok to leave the pressure turned down so that it runs thanks fasetester 🙂

[Author]

Posts