[fasetester]

Re: indeset

thanks dales for your reply it is the plastic front which houses the timer and the on off switch which has broke away with all the pulling to get the door open just when were on the subject where is the best place on line to get a selection of screw and nuts like m3 ect so the plastic front cant be bought bare does it come with all built in thanks. fasetester 😕

[fasetester]

thanks chris iam going to check it out all the best fasetester 🙂

[fasetester]

Re: hotpoint wf340p

thanks for your reply martin the machine seemed to be tumbling ok before i removed the pump and the blockage do you think the blockage could have caused the triac on the board to blow is there any way to test the board i covered the board and the motor with a carrier bag to stop them from getting wet what a place to put a board straight under the pump so holding in the start button for 3 sec would not have reset the program fasetester 🙁

[fasetester]

Re: hotpoint wf340p

thanks for your reply it is the fourth light down the time saver light jim do you think the machine just needs reset as the problum was a blockage after that the owner said the washed rugs in the machine i said the have bother washing clothes never mind washing rugs then when i went back to reset the son said it was working ok but when i contacted the mother she said it was not and was not paying and was buying a new machine so i told her if she did not want to pay that i would take the machine as payment as it was only 2 yrs old have not heard from her since last week so i rekon the retset the machine how do you get people to pay up as i am straight with people and said i would try and get the machine going for her 😡 fasetester

[fasetester]

hotpoint aquries

hi guys went to see a hotpoint aquries mod wf 430p 1300 problum was when it came to empy out and spin it stopped full of water empyed out water and removed pump rag stuck in pump removed hoses and checked seems ok but when the machine was restarted just keeps pumping out and flashing time saver light and on off light the on off light is flashing very fast does the machine need reset and if so how do i reset it or is there another problum thanks for any help fasetester. 😕

[fasetester]

Re: belling oven

hi martin it looks like the third one with the treaded mountings ele 2048 thanks. fasetester what price is the element 🙂

[fasetester]

Re: belling oven

thanks white van man and martin for you reply the only info i have from another supplyer is a element for synergie range belling elesv02 it looks like the element. from the fixing studs on the plate its measurment is5.7cm and from the bottom of the element to the top of the fixing plate it is 22cm and the in side is 19.8cm i checked around the oven but the only place i could see for the model number was inside the door but it had burned away if it says for the synergie range of oven would it not be the right element and if i were to remove the element to check the measurments and insulate the connections would the rest of the oven work ok until i completed the repair thanks. fasetester 😕

[fasetester]

Re: Seasons Greetings !! Ho Ho Ho

i would like to wish every one on ukw a very happy christmas and a happy peacful new year and thanks every one for your help 🙂 fasetester

[fasetester]

Re: creda simplicty 1000

can the striker plate that screws to the front of the interlock cause the lach on the door not line up right if it is wore. chris. 🙂 fasetester

[fasetester]

Re: Roads

might be a good place to start a car wash business 🙂 fasetester

[fasetester]

Re: creda simplicty 1000

hi martin it is a creda simplicty 1000 but i will have to check the model no and get back to you the next time iam in i just replaced the door hinge on the same machine its the second hinge in a short while why are the hinges so bad qualty its the mother in laws machine 😉 fasetester

[fasetester]

Re: creda simplicty 1000

thanks wilf and chris for your reply when you go to do a wash and give the door a slight slap it will work is that the spring on the lach what about the plate on front of the interlock could it be worn the striker plate thanks fasetester 🙂

[fasetester]

hi guys where has my tread gone on the creda simplicty 1000 door inter lock i was looking for it has some one removed it fasetester 😉

[fasetester]

Re: Seat Inca van

thanks welsh boy for your reply do the not have power assisted stearing 🙂

[fasetester]

What do you think of the citron berlingo? Are they a good van and have they any major faults? It’s the 1900 turbo. Do they have good lift or are they quite dead? What kind of pulling power? fasetester 🙂

[Author]

Posts