Forum Replies Created
-
Posts
-
Re: glass washer repair
hi john thanks for your reply no fault to repair at the moment just wanted to know if there was a web site or a forum out there just wanted to read up on them and get some experience or know how so i would know some thing about them as i would like get some experience in commercial appliance repair also thanks paul for your reply 😉 ps i know where to come if i have any problums fasetester
Re: Faulty Hotpoint Lam Brushes
hi what is the matter with the genuine hotpoint brushes all you hear is dont use non genuine brushes use the white holder ones from hotpoint now the word is use qualtex copyes i fitted a set of brushes to a hotpoint machine and a day later i got a call to say the machine had stopped washing again when i checked it the brush had come out of it holder has any one had this happen as when i fitted the brushes i had installed them properly and released them and pushed the retaining clip up to 90 degrees does the broad and narrow brush go by the size of the commuinter i ask was there any one at the machine as it seemed funny how the brush could get out you would think the only way that could happen was if the brush was relased and then pushed back in what are your thoughts fasetester 😮 thanks ps what price do you pay for your hotpoint brushes.
Re: Sale of Dangerous Parts to the Public.
hello guys would it not be better to train some one properly to do gas repaires or insulations than to let them carry out usafe repaires as the say a little knowledge can be a dangerous thing but if you want to go and learn properly the CITB just does not want to know as i tried to get trained a while back. fasetester 😕
Re: help please
yes eastlmark that is the name of it when you plug in appliance and press the test button two lights light one for insulation and another for earth the lights only for a few sec there is a timer that cuts them out you can check it on ebay iwent round to see it as he lives local 🙂 fasetester
Re: servis m6013s-1 door seal
hi penguin thanks for the information on fitting the door seals 🙂 fasetester
Re: AAAAAaaaaarrrrgggghhh!!!!!!!Zanussi door seal.
hi clive could you send a picture and some details of your tool for fitting the door seal spring thanks 🙂 fasetester
Re: servis m6013s-1 door seal
hi just when you are talking about door seals is there any easy way or tips on fitting zanussi door seals or on any machine that you cant remove the front to fit the seal and have to fit it through the door and try and get the the steel spring band back over the inner lip complete night mare is there any type of clamp you can use to help keep it in place while you try and get it on thanks 😕 fasetester
Re: help please
thanks for your reply just a fellow is selling one and i was wondering if any one had any experience of that type so if the do the job it does not matter what make the are as long as the are working properly 🙂 fasetester.
Re: Bespoke kitchen ding dong!
so in other words there is no short cuts or tips for easy removal of built in appliances just hard graft some times there is no easy way the kitchen fitters and tilers must think the will never have to be removed and is there any kind of tool for ajusting the plastic legs on these appliances 🙁 thanks fasetester.
Re: Bespoke kitchen ding dong!
thanks for the reply bill the intergrated appliances are a total nightmare the house holder think you can take the kitchen apart and re build it and the say its no good to me like that and the tilers just tile about half way in under the appliance you know your self the problums 😡 fase tester
Re: Bespoke kitchen ding dong!
hi is there any tips or tricks getting these appliances out of the kitchen units as i went to repair a intergrated dishwasher for a start the taps and waste pipe were behind the back wall of the sink unit when i got that removed and turned off and removed then tried to remove the dish washer it would only come out so far then the back legs would catch on the tiles then when you ajusted the front legs to get clearance it would jam against the work top what a night mare 😡 fasetester
Re: intergrated dishwasher
Martin wrote:
fasetester wrote:
yes martin i do work at appliancesWork at appliances is what most of our trade members are at anyway 😉
I will put my question another way then, do you make a living from repairing dishwashers and the like? you could say that martin i think it would be a good experience and to learn from other professional people like your self and add some thing to the site when i learned something usefull thanks. 🙂
Re: intergrated dishwasher
Martin wrote:
fasetester wrote:
as i have broke the back legs on a fewAre you a trade member? It appears that you are in the trade after all, and with trade access you can ask your technical questions there. Rather than here in the public forums 🙂
yes martin i do work at appliances but i dont know if i would be able to get into the trade forum thanks for asking me . 🙂
Re: intergrated dishwasher
Dales-Electronic wrote:I think you have answered your own question – kitchen fitters!
thanks for your reply is there a easy way round getting intergrated appliances out of kitchen units as i have broke the back legs on a few when you ajust down the frount legs to get clearance you get them out so far and then the back legs get caught on the tiles because most tilers dont tile to the back wall and you cant get at the back legs to ajust them down is there any tips on removing them thanks .
hi thanks for the reply does the flood protection not only work if there was a leak or the dishwasher over filled and would bring in the pump to clear the the over fill and what do you mean by a choked water fill matrix and where do i find it and where do i find zaunissi iwms thanks penguin 45. fase tester
hi thanks for your reply do you mean the pressure switch is blocked and where do you find the syphon tubes the problum would have nothing to do with the electronics or the control panell need resetting thanks lotusray. fase tester 😕
