[fasetester]

Re: hotpoint ma door wont open

thanks for your reply electrofix what do you mean all i know is the door wont open and the door lock light does not flash just steady on at the end of the program and if you try to reset the program the light does not flash but the program is working ok any tips on getting the door open fasetester

[fasetester]

Re: puppy

thanks guys for the replys as you say perseverence is the way 🙂

[fasetester]

hi subs i sent you a pm look in your in box fasetester 😉

[fasetester]

so what you are saying is even if you test the capactor with the meter and get it to charge and dischare and you get the flick on the meter the capactor could still be faulty that what i went with all along and if i did not get it to charge or discharge changed the capactor and the motor burst into life so i could be fooled going by the meter so you are best just to try a new one that is the only sure way thanks penguin and dpm any more comments on the hose clips on this washer pump the dont seem very tight when you have removed them put them back on the seem kind loose and with the pressure of the pump you would think the would blow off or do the not have to be over tight and do any of you know of the metal bands that subs is talking about thanks for all the replys fasetester

[fasetester]

Re: indesit dishwasher

thanks for the reply penguin would you say that testing the capactor with a analog meter to charge and discharge the capactor would not give the proper results so far that is how i have tested them and it has so far told me if the capactor was a dud what do you think penguin thanks faseester 🙂

[fasetester]

what kind of bands subs are the and what do you ask for are the like cable ties only metal do the come in different sizes and are the expensive subs have you ever changed a capactor that you thought was ok for a new one on a washer motor and for it start working thanks fasetester

[fasetester]

thanks jonnyj when i test the capactor it was chargeing up and discharging usally you will get open circuit or shorted or has any one tested the capactor and seemed ok but changed it for the motor to work thanks fasetester

[fasetester]

thanks for the reply hotpnt after it fills you can hear the washer pump like trying to kick in it will hum and then try to turn as if it is a lazy motor are the known for motor failure when the hose is recrimped will the seal ok again as the dont seem that tight you would think with the pump pressure the would blow off are the a sealed motor thanks fasetester

[fasetester]

Re: indesit dishwasher

went to see dishwasher indesit after pumping out at the start of the program would fill in with water but no wash action i could hear the washer pump trying to go as if it was trying to start tested capactor seemed ok removed washer pump to check for blockages pump turned freely is there any thing else i should have checked removed empying pump checked ok would it be possible for the washer pump to have weak windings and stop it from washing and the hose clips are hard to get back on the washer pump hard to get them to click into the second nick or is there a tool for the job the keep sliding round if i could hear from any hotpoint indesit engineers what the think could be wrong thanks fasetester 😕

[fasetester]

Re: creda dryer

hi guys it a while from i worked on one of these dryers how is the front face held on how do i remove it does the timer have to be removed thanks for any help i could have got the model number wrong it is t522vw 🙂 fasetester

[fasetester]

Re: creda dryer

thanks for the reply helo75 would there be much slack to change the switch that way up throught the top the thing is customer rung said child was at the dryer and broke the door catch is it just a push and pull on this dryer or a lach type like washing machine the said the replaced the door catch but still would not work the said the have a new door switch and would i come and fit it the migh have fitted the door latch wrong fase tester 🙂

[fasetester]

hi martin and guys is that a problum with all non genuin heating elements or just the bosch would you say always go for genuin if possible fasetester

[fasetester]

Re: Ariston motor fault

dpm does that mean scrap metal has gone up in price or just copper fasetester 🙂

[fasetester]

did not know it was faulty belt jim until i went to see the machine that would have been simple until i turned the drum the bearings were well gone the main reason why the belt had come of seem to be getting more loosers than winners fasetester 🙁

[fasetester]

thanks for all the help but now the dont want the machine fixed just have to file the info for another day 😥 just seem to hit non fixers fasetester

[Author]

Posts