[fasetester]

Re: indesit timer spins around

thanks richard for your help so the first thing i need to do is open the door and then put the power on at the socket and then select a stop poition on the timer help much appreciated fasetester 🙂

[fasetester]

Re: Connect next day delivery? Am I just unlucky?

what part of n ireland did you move to rickshaw fasetester 🙂

[fasetester]

Re: refund for book

thanks richard and ken for your reply i had 30 days to return the book how long do you have to look for a refund thanks fasetester 🙁

[fasetester]

Re: Hotpoint oven help

or even a couple of clothes pegs will work if you have nothing else fasetester 😕

[fasetester]

Re: Hose clip pliers

bobokines are the for the steel spring hose clips the ones you have pull in and do the do all sizes of clips thanks fasetester 🙂

[fasetester]

Re: hoover door hinge

thanks guys for the replys fasetester 🙂

[fasetester]

Re: hoover door hinge

thanks for the reply peng so is there a weaker hinge and a better quality one or are the all much the same the are not very strong would you put in new retainers when you are changing the hinge fasetester 🙂

[fasetester]

Martin wrote:I refer you to my previous post: –

Martin wrote:
The module is faulty and needs replacing as does the Interlock.

Very common fault where the Interlock shorts out internally and takes the Module with it…..!!!!

why does the manufacture not put a in line fuse between the interlock and the board would that not save the board when the interlock would short out what do you think fasetester

[fasetester]

Re: hotpoint Wma door wont open

thanks chris and all the guys for your help went back to machine the interlock was missing a N connection traced wire back up to the board and the neutral on the board had blowen tryed to bridge the blowen connection but the track had come away from the board what would be the most likly cause for that happening when i showed it to the woman she said that must have been the bang i heard now she tells me could you connect the neutral from the interlock to another neutral in the machine dont think it would work as you are still missing the neutrals from the board what do you guys think thanks fasetester 🙂

[fasetester]

Re: beko

thanks chris for your reply if only it would play up when iam their have to wait and see how long it goes for fasetester 😕

[fasetester]

Re: beko

thanks cab for the reply do you think it could be a intermittent water valve or a blockage in the system fase tester 🙂

[fasetester]

Penguin45 wrote:Look, this is very simple to sort. Slip the door seal and pull the lock out on its wires. Set the machine to spin, push the lock slider across and hit start. Give it a couple of minutes to warm through, and press cancel. After it all stops, if you’re still getting 240v at the lock, the board has a fault. If you haven’t got volts, it’s a sticky lock and needs replacing.

Chris.

thanks chris for you opion when i press off there is no juice so i will replace interlock fasetster

[fasetester]

Re: hotpoint Wma door wont open

hi guys went to see the hotpoint ma 61 got the door open checked interlock after the time is up the door is not releasing the power is disconnected from the interlock when the on off switch is pressed off checked circuit board cant see any damage the woman want me to try new door switch can the board be removed from the timer or is it all in one if the interlock does not fix the machine is there some where that checks the board and what kind money would a repair be thanks fasetester 🙁

[fasetester]

Re: hotpoint ma door wont open

thanks martin could be a costly repair any tips on opening the door in your experince mostl likely the board is that why the door lock light is not blinking have to go at 10am the interlock would not be the problum so you are talking about how much for a board thanks fasetester

[fasetester]

Re: hotpoint ma door wont open

thanks electrofix can the interlock fail in the closed posion what does it mean by the door lock lite not blinking and how do i get the door open any hotpoint engineers care to comment or any engineer that has had this problum i have to go and check it out tomorrow all help appreciated thanks fasetester 😕

[Author]

Posts