funkyboogy

Forum Replies Created

Viewing 15 posts - 2,116 through 2,130 (of 2,407 total)
1 2 3 … 141 142 143 … 159 160 161
  • Author
    Posts
  • February 13, 2007 at 9:54 pm in reply to: tricity bendix electric cooker stat req #204206
    funkyboogy
    Participant

    Re: tricity bendix electric cooker stat req

    cheers chris…
    will check these out…
    ally

    February 13, 2007 at 9:45 pm in reply to: MFI DIPLOMAT OVEN #171789
    funkyboogy
    Participant

    Re: MFI DIPLOMAT OVEN

    diplomat ovens are being made by beko now….
    after mfi cooker factory in stockton was shut last aprill….
    these cookers do conform to eu standards…

    my mate used to work for them and has a few stories,
    funny enough all about their cookers…

    ally….

    February 13, 2007 at 9:16 pm in reply to: hotpoint washer dryer wd860p #204278
    funkyboogy
    Participant

    Re: hotpoint washer dryer wd860p

    think this one for the merloni guys…
    they hopefully will have a secret no…
    cheers ally

    February 10, 2007 at 5:03 pm in reply to: KENWOOD DISHWASHER DWD 24FI #203886
    funkyboogy
    Participant

    Re: KENWOOD DISHWASHER DWD 24FI

    cheers…

    February 9, 2007 at 8:23 pm in reply to: RANGEMASTER TOLEDO 90 S/S #203820
    funkyboogy
    Participant

    Re: RANGEMASTER TOLEDO 90 S/S

    cheers kirk…
    ally

    January 24, 2007 at 8:14 am in reply to: Whirlpool AWM6110/3 Washer out of sequence #202044
    funkyboogy
    Participant

    Re: Whirlpool AWM6110/3 Washer out of sequence

    normally you would just keep start button pressed in for 5-10 seconds to clear memory/resett?
    ally…

    January 22, 2007 at 9:42 pm in reply to: DO YOU TELL THEM #201636
    funkyboogy
    Participant

    Re: DO YOU TELL THEM

    the point i was trying to get across is

    i am completely astounded by people who buy washing machines for under £200, and think they have bought a rollsroyce..and complain about it breaking after only 6 months…
    and when you call to give them a rough idea of time your are likely to call they want you to give them the precise minute of when your going to arrive..
    they want top dollar after-sales… again what did they think they were buying for under £200…???
    ally

    January 21, 2007 at 10:35 am in reply to: SERVIS M6011-1 #201616
    funkyboogy
    Participant

    Re: SERVIS M6011-1

    cheers mike, it is under warranty…
    bought as prezy cant find receipt etc..
    ally

    January 20, 2007 at 12:39 pm in reply to: PROLINE PDW 080 #201491
    funkyboogy
    Participant

    Re: PROLINE PDW 080

    indesit one will do, ive fitted lots of them…
    part c00041086…
    ally

    January 16, 2007 at 10:03 pm in reply to: SMEG RANGE COOKER SUK 91MFX5 #201088
    funkyboogy
    Participant

    Re: SMEG RANGE COOKER SUK 91MFX5

    cheers

    January 14, 2007 at 9:33 am in reply to: schreiber cooker #200708
    funkyboogy
    Participant

    Re: schreiber cooker

    cheers chris..

    January 13, 2007 at 6:24 pm in reply to: Samsung RS21DCNS Icemaker flap #200680
    funkyboogy
    Participant

    Re: Samsung RS21DCNS Icemaker flap

    done a lot of samsung work, not had any probs with ice maker flap..
    infact you wont get to much trouble from these appliances
    main prob …twin cooling panel in fridge goes faulty…
    causing high temp in fridge, noise in fridge, and not water to dispensor..
    easy to fix…in and out 20-40 mins..

    good money if chargable…
    ally

    January 13, 2007 at 6:16 pm in reply to: Hotpoint CTD00P #200639
    funkyboogy
    Participant

    Re: Hotpoint CTD00P

    the way i usually fit belt is….

    remove lid,and both side panels,2 screws that hold water bottle holder ,split pin @ shaft,
    take heater out of way by removing plug situated next to capacitor,remove rear fan..
    take out 2 screws next to mains terminal..this will now allow you to pull back panel back enough to slip belt over drum..
    now refit rear panel ,split pin, and right side panel…
    @ left side remove inner fan housing (just pops of) remove inner fan.
    loosen pulley assy..take nearest bolt right off , slip belt over motor shaft and align… adjust pulley as req..
    refit inner fan etc, job done…
    tried a few other ways, but this is the fastest…about 30 mins 1st one…
    cheers ally…

    January 11, 2007 at 8:36 pm in reply to: diplomat/hygena #200412
    funkyboogy
    Participant

    Re: diplomat/hygena

    cheers bryan…

    January 9, 2007 at 3:45 pm in reply to: BOSCH AMERICAN F/F K3915 #199994
    funkyboogy
    Participant

    Re: BOSCH AMERICAN F/F K3915

    cheers greg…
    tried searching model no, and nothing came up either…going to app tomorow…
    will update asp
    cheers ally

  • Author
    Posts
Viewing 15 posts - 2,116 through 2,130 (of 2,407 total)
1 2 3 … 141 142 143 … 159 160 161