geoff1

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 409 total)
1 2 3 4 5 … 26 27 28
  • Author
    Posts
  • January 20, 2014 at 10:41 pm in reply to: Hotpoint WMUD 10637 washing machine #407919
    geoff1
    Participant

    Re: Hotpoint WMUD 10637 washing machine

    Hi

    I had one that I could not get to reset and spoke to Hotpoint.

    was told to start program and leave it for up to 1hr. during this time it would start to fill.
    HMM
    Tried it but could not stay so returned later just in time to see the water level approaching the soap draw. Was not away for the full time

    Stopped it and emptied drum.

    It was OK from there on.

    Geoff

    January 19, 2014 at 3:30 pm in reply to: BEKO WME7267W #407761
    geoff1
    Participant

    Re: BEKO WME7267W

    Hi

    Have sent some information to email address on your web site

    HTH

    Geoff

    January 10, 2014 at 3:17 pm in reply to: whirlpool akz511/1x 858551115000 #407434
    geoff1
    Participant

    Re: whirlpool akz511/1x 858551115000

    Hi Colin

    Thank you for your help.

    Geoff

    January 9, 2014 at 4:36 pm in reply to: dead beko cf5533apw – compressor relay or pcb? #407143
    geoff1
    Participant

    Re: dead beko cf5533apw – compressor relay or pcb?

    Hi

    I had one similar about 5 months ago and changed blue capacitor on module top rear which worked OK.

    Part number for rear module if you need it is 4360620185

    Geoff

    January 7, 2014 at 5:34 pm in reply to: Hotpoint BF162 overfilling #407327
    geoff1
    Participant

    Re: Hotpoint BF162 overfilling

    Hi

    Yes checked the wiring and I get feed from pressure switch to dispenser. But even though the pressure has clicked over the valve keeps on filling. only when you reset program/open door does it stop.
    Sorry it should be BFI62 for the model

    Geoff

    November 28, 2013 at 8:47 pm in reply to: Belling 600x #405426
    geoff1
    Participant

    Re: Belling 600x

    Thanks Martin but this one is for top oven and dont think I can adapt for main oven.

    Geoff

    November 11, 2013 at 10:35 pm in reply to: Hotpoint HV7F140 – how old #404309
    geoff1
    Participant

    Re: Hotpoint HV7F140 – how old

    Hi

    Many thanks for help

    Geoff

    November 8, 2013 at 8:37 pm in reply to: Whirlpool ADG7560/1 BI dishwasher #404152
    geoff1
    Participant

    Re: Whirlpool ADG7560/1 BI dishwasher

    Hi Colin

    Many thanks for the very useful information.

    Most appricated

    Geoff

    November 8, 2013 at 4:30 pm in reply to: Whirlpool ADG7560/1 BI dishwasher #404151
    geoff1
    Participant

    Re: Whirlpool ADG7560/1 BI dishwasher

    Hi Colin

    geoffmason705@btinternet.com

    many thanks

    Geoff

    October 30, 2013 at 10:51 pm in reply to: Beko CU7230 small drive belt/pulley #403655
    geoff1
    Participant

    Re: Beko CU7230 small drive belt/pulley

    Hi

    If this is the DCU7230 the part number is 492204404.4phe285

    This is for the condensor dryer where the pulley and motor are on rhs looking from front.
    Hard part is all the screws etc to take out to remove the motor but belt and pulley go on easily.

    The one bazza is on about is vented dryer and motor/pulley is fitted on lhs looking from front which is a nightmare to fit as well as plenty of plasters needed This one has an uprated belt to 5PE and new pulley. 492204403 5phe226

    hope this is ok

    Geoff

    September 24, 2013 at 1:29 pm in reply to: Beko integrated dishwasher overheating #401699
    geoff1
    Participant

    Re: Beko integrated dishwasher overheating

    Hi

    I am sure that you will find that the relay contacts on the module are stuck together giving a permanent live feed to heater.

    thermal fuse in heater does not activate in ones that I have been to!!

    Geoff

    September 23, 2013 at 1:40 pm in reply to: AEG fridge 923523608 K8-12-001 #401641
    geoff1
    Participant

    Re: AEG fridge 923523608 K8-12-001

    Hi Cras

    2425006034 is power module situated behind display module

    2425009012 is display module

    Regards

    Geoff

    August 23, 2013 at 5:05 pm in reply to: Smeg SUK91MFX oven selector switch problems #382661
    geoff1
    Participant

    Re: Smeg SUK91MFX oven selector switch problems

    sorry

    cannot spell

    could you resend on geoffmason705@btinternet.com

    I cannot spell internet

    many thanks

    Geoff

    August 22, 2013 at 4:22 pm in reply to: Smeg SUK91MFX oven selector switch problems #382659
    geoff1
    Participant

    Re: Smeg SUK91MFX oven selector switch problems

    Bump

    anyone one got any thing please

    Geoff

    August 21, 2013 at 3:58 pm in reply to: Smeg SUK91MFX oven selector switch problems #382658
    geoff1
    Participant

    Re: Smeg SUK91MFX oven selector switch problems

    Hi

    Can anyone help me with this bulletin as I am having same problem.

    email geoffmason705@btinertnet.com

    Appricate your help

    Geoff

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 409 total)
1 2 3 4 5 … 26 27 28