[geoff1]

Re: Hotpoitn WMD960

Hi

I took the upper panel to another machine that I was putting bearings in and it worked ok with that one. Sent module back to EMW and they sent me a completly different one which has worked no problem. I also retighted all the connections on the module as well.
Hope you manage to sort yours

Geoff

[geoff1]

Re: Fridge – Freezer Hygena APM6855 Door required

Best to try AWS on 01603 412324

when you phone have full model number apm6855 or apm6855/01, serial number and date of purchase if possible as there are two versions.

Geoff

[geoff1]

Re: Hobart CHF40 No heat

Hi

If you send me your email address I will send you some bed time reading for this machine.
When the machine has filled do you hear a loud clunk which is the contactor engaging to supply the boiler tank heaters? Is the pressure chamber clear and switch activating?
Have you been able to check the resistance of the boiler tank elements as well as the wash tank element?

Just some possibilities

Geoff

[geoff1]

Re: bosch door handel part number was24460gb/08

Hi

Bosch only list door assy on 704286 or the catch on 623234

This looks like it could be a bit expensive for a handle

Geoff

[geoff1]

Re: Bosch SGS43c12GB15

Hi

I tried the pul the plug out trick just in case. As you said it can work sometimes.

Will try and get back to morrow to go back over everthing again just to make sure and quote for module if everything is ok

Any many thanks for advice

Geoff

[geoff1]

Re: Hotpoitn WMD960

Thank you for your repply

I Checked the plug at the time and all is ok but it does not rule out the door lock itself.Other than that I back to the upper module 😕

geoff

[geoff1]

Re: Bosch SGS43c12GB15

Hi

Yes it heats up ok on quick wash and no problems on insulation test.
It is at the point where it empties to start to fill for the hot wash that it all goes wrong.
Both motors just sit there in turn switching on and off and no water goes in

geoff

[geoff1]

Re: Hotpoitn WMD960

Well been back to day with another module and it is no different. tried new motor with no luck. checked wiring between motor. upper module, heater and pump.

Door will lock and will start programme. there is live to valves, motor and pump but no neutral which is controlled by the module.

Has anyone had this before or got any ideas as I have run out

Geoff

[geoff1]

Re: Bosch WAS32469GB/20

Hi

Found it on Bosch site

616876 door lock

704286 door assy only available

HTH

Geoff

[geoff1]

Re: Hotpoitn WMD960

Hi Jim

Many thanks for information.

will go back next week better armed.

Geoff

[geoff1]

Re: Dead WMA11!

hi

I had a similar problem a few years back and what I found was that I had reversed 2 wires on module ( they sit in a little block next to the selector unit) One wire goes to the pressure switch and if reveresed will stop power going to module once water level is up.Looking down on module the brown/green wire to pressure switch is on left and the red/green that goes to heater is on right
Also check valves are ok

Geoff

[geoff1]

Re: Amica AWP510L

Thanks Dave

It turned out to be a pulley problem – no codes where being displayed when I got there. Thanks for the information on where to look

Geoff

[geoff1]

Re: Tricity Bendix BIW105W…pnc 914213009 01

Hi Rob

have emailed some information to you on the module I suspect the machine has.

Sent to email on your website.

HTH

Geoff

[geoff1]

Re: stoves energy regulator

Hi

Try 082590800.

Geoff

[geoff1]

Re: Beko WM6143W

Hi

Part number for door assy is 2860205400.

Dont have a hadle kit would need to know which part you needed

Geoff

[Author]

Posts