Forum Replies Created
-
Posts
-
Re: SMEG DI6 FABP (0102008741) Dishwasher Problem
Thank you for the info’… you must have come across this problem before.
Best wishes,
jonty
Re: SMEG DI6 FABP (0102008741) Dishwasher Problem
Thanks,
I’ve brought the dishwasher to my workshop, and run it up again.
It drains and fills well, and washes for around three minutes, before draining and aborting the cycle.
When it aborts five beeps are sent, and the two programme lights, (four and five from the left) next to the programme selection button are lit. These two lights incorporate the end of cycle status, number “four” flashes, and number five remains constantly lit.
The small display doesn’t send any message/error code.
Can you, or someone decipher the above, which would be a great help!
jontyRe: LG Condensor Tumble Dryer RC9011A "clean filter" light
I’ve finally ascertained that the sensor in question is a TOC ‘stat.
Does anyone know if this sensor would cause the above problem? I assume that it measures the air flow/density, and if faulty sends the clean filter light on.
jontyRe: LG Condensor Tumble Dryer RC9011A "clean filter" light
Does anyone have a manual, or is there a test procedure for this dryer?
I’ve located a sensor behind the lint filter,(and wonder if this is some sort of turbidity sensor?) in the housing, but unable to find it on a parts diagram, and it may not be faulty anyway.
Any help gratefully accepted!
jonty
Re: Bosch Classixx SMS40C02GB Dishwasher Error Code E09
Any help would be much appreciated.
Has anyone experienced such a fault, as the m/c is under three years old?
I don’t want to replace the control module if it is fine!
jonty
Re: Creda W220VW washing machine Fill Problem/s
Renewed fill valves… cured fault!
Suspect faulty solenoid.
Thanks again folks.
jonty
Re: Creda W220VW washing machine Fill Problem/s
Agreed, but I wonder why the m/c initially fills perfectly?
Jon
Re: Creda W220VW washing machine Fill Problem/s
Thank you electrofix and iadom,
Returned today, and carried out the Test Sequence as per manual.
This confirmed Error Code: 2 – Failure to set pressure switch in 94 seconds.
The pressure chamber is clear, and the p/s hose is fine.
I haven’t tested the water valves yet, as it initially fills perfectly well.
Could e/fix let me know if pressure bell means bellows, as I replaced the p/switch prior to the module/board.
Kind regards,
jonty
Re: NEFF W5420X0GB/30 Washing Machine Beep & LED Error Codes
Good afternoon,
Having checked the wiring harness, and connections, I deduced that the power module was faulty.
Renewed above yesterday…all well.
Re: NEFF W5420X0GB/30 Washing Machine Beep & LED Error Codes
p.s.
Does anyone know where these codes can be obtained from, other than
NEFF/Bosch/Siemens, who will only inform their own engineers of such codes.
jonty
Re: NEFF W5420X0GB/30 Washing Machine Beep & LED Error Codes
Mmmm,
Hopefully I can obtain these error codes, which would be beneficial.
jonty
Re: NEFF W5420X0GB/30 Washing Machine Beep & LED Error Codes
Thanks Martin,
Will return, and investigate further.
Do you, or anyone know if a motor fault could prevent the door interlock from functioning?
Regards
Re: NEFF W5420X0GB/30 Washing Machine Beep & LED Error Codes
Hello Martin,
I haven’t been able to test too much, as I was hoping to ascertain what the machine is trying to signal.
As mentioned, the door does not lock, so tested it.
Also ensured filter/housing clear, as customer thought the three beeps relate to drain problem.
The machine will not start on any programme, so a little limited until error codes verified.
jonty
