Forum Replies Created
-
AuthorPosts
-
keithwilliams
Participantthis is a shot in the dark. i have twice been to a whirlpool washer which instantly threw up a heating related fault. closer inspection revealed the heater relay on the pcb had stuck in the on position. never had this on a bosch but theres always a first time i suppose.
keithwilliams
Participantcan i jump in here? my customer will abort any heated cycle so i have suspected the ntc. can you tell me what the room temp value of this is lease, or better still exactly which one youd recommend.
many thanks
kJune 26, 2018 at 6:27 am in reply to: miele cond dryer T8822c “clean out airways” after 20 mins #456457keithwilliams
ParticipantRe: miele cond dryer T8822c "clean out airways" after 20 m
Thanks for that.
I have thoroughly cleaned everything. Including fan impeller blades.
I haven’t been back yet.
My next move is to reprogram the drying cycle to be more tolerant.
Also I’ll tske readings on sensors as suggested although I don’t think they are faulty as it will happily run another 20 mins immediately after it initially stops.
I will report back if I get it running longer.
Kkeithwilliams
ParticipantRe: Ignis ADL350/1 dishwasher pump only.
Yes I agree. I was hoping for specific components. In absence of anything obvious I gave the relays a smack and so far it’s still working.
keithwilliams
ParticipantRe: Ignis ADL350/1 dishwasher pump only.
Did anyone get to the bottom of this please
keithwilliams
ParticipantRe: aeg l76800 pnc 914003087 00 cuts out after 1 second
sorry forgot to reply. yes insulation all okay. shes binned it now anyway. wouldve loved the chance to find out what it was.
thanks
kkeithwilliams
ParticipantRe: john lewis dryer
and sometimes the fuse resistor next to it. i think its 47r. the grey one.
keithwilliams
ParticipantRe: How possible at the price?
having a bit of fun this morning.
emptied my qualtex basket and ordered each item individually from their lm electrical shop. going to keep the couriers busy.keithwilliams
ParticipantRe: How possible at the price?
they must be making lots of mistakes.
trade price to me for a fan motor mtr303 £22.99 plus vat and of course carriage if only item ordered.
went on ebay found an equivalent to the hotpoint original for 19.95 delivery included.
yes you’ve guessed it, it was from qualtex.
so qualtex trade price inc carriage £35.98
ebay (lm electrical inc carriage £19.75
i think they have a cheeck sponsoring some of this site while at same time selling cheaper to public
February 28, 2018 at 9:23 am in reply to: hotpoint twin energy regulator wiring configuration #454170keithwilliams
ParticipantRe: hotpoint twin energy regulator wiring configuration
i hope this works for you. its my first attempt at posting pictures.
February 24, 2018 at 9:09 am in reply to: hotpoint twin energy regulator wiring configuration #454168keithwilliams
ParticipantRe: hotpoint twin energy regulator wiring configuration
got the info if you still need it.
February 21, 2018 at 7:24 pm in reply to: hotpoint twin energy regulator wiring configuration #454167keithwilliams
ParticipantRe: hotpoint twin energy regulator wiring configuration
im going to repair one iof these either tomorrow or friday.
if youve heard nothing by then, i’ll take a picture for you.keithwilliams
ParticipantRe: Qualtex Account Closure
This is genuine stuff as well but I suppose the same logic applies. Four more items out of stock since I first posted.
keithwilliams
Participantqualtex "out of stock"
is it just me being unlucky?
this last ten days or so ive attempted to order at least 20 different items that i would call usual stock, only to consistently find them listed as out of stock. as masterpart were my other usual supplier, i’m seriously looking to revitalise some extinct accounts.how do you guys find electrue or homespare just now.
i should say ive found maddocks stock to be sketchy as well when looking with a mates log-in
keithwilliams
ParticipantRe: candy double oven FDP232x oven fan motor required
thanks for your info don.
believe it or not that part number on gen hoover site is for washer dryer fan motor.
but i trust you to be correct. i’ll measure the spindle against a Beko motor when it arrives.regards
keith -
AuthorPosts
