keithwilliams

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 415 total)
1 2 3 4 5 … 26 27 28
  • Author
    Posts
  • July 9, 2015 at 8:24 pm in reply to: Hoover VHC 391/1-80 #428434
    keithwilliams
    Participant

    Re: Hoover VHC 391/1-80

    could be wrong but ive had these with the heater relay on the pcb being faulty.

    May 28, 2015 at 10:47 pm in reply to: rubbish non genuine dryer capacitors #427621
    keithwilliams
    Participant

    Re: rubbish non genuine dryer capacitors

    yes go in through the fan housing. mind you 2 minutes is a bit of an exaggeration. more like 15.

    May 5, 2015 at 6:30 pm in reply to: emw1000 pcb blown resistor #426959
    keithwilliams
    Participant

    Re: emw1000 pcb blown resistor

    similar but not identical board, resistor was reading 47ohms.
    posted for info. will put in something around 70ish and see what happens.

    April 30, 2015 at 4:43 pm in reply to: MAYTAG 21PNDGW No drum action #394129
    keithwilliams
    Participant

    Re: MAYTAG 21PNDGW No drum action

    yes thanks
    customer ordered pcb £200 ouch!!!!
    but it fixed it.
    got old one to play with when got time.

    April 6, 2015 at 8:47 pm in reply to: MAYTAG 21PNDGW No drum action #394127
    keithwilliams
    Participant

    Re: MAYTAG 21PNDGW No drum action

    did you get this machine running? if so what was it. I have a similar machine but motor board is obsolete.
    ta

    March 11, 2015 at 6:06 pm in reply to: beko dw601 #425474
    keithwilliams
    Participant

    Re: beko dw601

    had these symtoms a while back. in the end a pcb cured it. quite cheap at about £20. in fact its worth carrying one anyway.

    February 26, 2015 at 6:35 pm in reply to: Hoover dyc 8813b no supply to heater #424844
    keithwilliams
    Participant

    Re: Hoover dyc 8813b no supply to heater

    I cant remember which model, but I have had a no heat fault due to relay on pcb. soldered in a new one and away she went.

    February 5, 2015 at 5:34 pm in reply to: bosch wvd2452bgb stuck on 1 minute #424406
    keithwilliams
    Participant

    Re: bosch wvd2452bgb stuck on 1 minute

    thanks
    will try to get a look tomorrow.
    will report back.
    k

    February 2, 2015 at 8:22 pm in reply to: Beko CTD MODEL.DCU7230 #412167
    keithwilliams
    Participant

    Re: Beko CTD MODEL.DCU7230

    any chance of telling us what fixed this in the end please. I didn’t check ntc either but if that’s what fixed yours then I don’t need to order a pcb.
    to be honest these are only 180 quid at mo so she might not buy a pcb anyway.

    thanks

    January 27, 2015 at 7:04 pm in reply to: smeg dishwasher leak #424069
    keithwilliams
    Participant

    Re: smeg dishwasher leak

    deffo O-rings first.or sometimes ive seen the locking ring that fastens fill chamber to tub side come loose.

    remove the lower panel and set a cycle running while lying on floor with torch pointing to right side. look for dribbles.

    January 11, 2015 at 6:34 pm in reply to: Bosch Dishwasher #423340
    keithwilliams
    Participant

    Re: Bosch Dishwasher

    I know this sounds daft. but on at least four occasions ive cured e24 by removing crap from the circulation pump impellor. why e24? I don’t know, but there you are

    December 29, 2014 at 4:29 pm in reply to: lamona 8300 dishwasher boiling when finished #421145
    keithwilliams
    Participant

    Re: lamona 8300 dishwasher boiling when finished

    heater relay contacts on pcb weld themselves together.
    potentially a worrying fault. boards are cheap to buy though so no need to replace relay.

    October 25, 2014 at 8:43 am in reply to: Zanussi ZWG1140M – Pump rattle #420658
    keithwilliams
    Participant

    Re: Zanussi ZWG1140M – Pump rattle

    can i just point out that in my experience most people who complain about chinese junk, tend to have i phones, i pads,i macs
    etc. where do they think this stuff is made

    October 17, 2014 at 5:34 pm in reply to: SMS50E02Uk/01 dish washer #420510
    keithwilliams
    Participant

    Re: SMS50E02Uk/01 dish washer

    i’ve had this fault code many times and it has always been stuff stuck in the spraypump impellor. i know what youre thinking, but trust me.

    July 14, 2014 at 6:51 pm in reply to: whirlpool awor4205 washer #401093
    keithwilliams
    Participant

    Re: whirlpool awor4205 washer

    found this board listed in “simple pcb repairs” the two components i spotted are mentioned plus one other. so parts ordered.

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 415 total)
1 2 3 4 5 … 26 27 28