kevinlewis

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 152 total)
1 2 3 4 … 9 10 11
  • Author
    Posts
  • November 21, 2013 at 12:01 am in reply to: miele t494c dryer #379081
    kevinlewis
    Participant

    Re: miele t494c dryer

    did you have to undo the six bolts for the removal of the backplate before you gain access to these two hidden bolts?

    October 28, 2013 at 10:37 pm in reply to: Neff gas hob #403551
    kevinlewis
    Participant

    Re: Neff gas hob

    sorry, its on the customer’s hob. Bosch and siemens used the same box.

    October 15, 2013 at 3:25 pm in reply to: Bosch Obsolete Ignition box replacement? #332109
    kevinlewis
    Participant

    Re: Bosch Obsolete Ignition box replacement?

    Neff T2113wogb/03 same problem same part number but ignition box now subs to 068992 . BSH saying part no longer available. any suggestions?

    August 15, 2013 at 7:19 am in reply to: ASD Services #399357
    kevinlewis
    Participant

    Re: ASD Services

    Thanks for that information. I must have been using them for over 30 years. Very sorry to hear they have closed down.

    July 9, 2013 at 12:48 pm in reply to: logik spare parts #397363
    kevinlewis
    Participant

    Re: logik spare parts

    had trouble with connect’s B2B website.you can purchase from connect.Thanks

    July 9, 2013 at 11:36 am in reply to: hotpoint tumble dryer tcm570p #397226
    kevinlewis
    Participant

    Re: hotpoint tumble dryer tcm570p

    condensor never been cleaned in 3 years. now working fine. thanks.

    July 9, 2013 at 11:34 am in reply to: logik defrost timer #396199
    kevinlewis
    Participant

    Re: logik defrost timer

    yes i could but customer wants to fit it himself and it would mean cutting and recrimping the correct spades.

    July 5, 2013 at 9:57 am in reply to: hotpoint tumble dryer tcm570p #397225
    kevinlewis
    Participant

    Re: hotpoint tumble dryer tcm570p

    thanks guys. booked in for tuesday.

    June 11, 2013 at 10:32 am in reply to: inesit wd10 not heating #395171
    kevinlewis
    Participant

    Re: inesit wd10 not heating

    thanks for that. the heat fuse microtemp had blown caused by the fan open circuiting. now working fine. thanks again

    May 28, 2013 at 2:30 pm in reply to: inesit wd10 not heating #395169
    kevinlewis
    Participant

    Re: inesit wd10 not heating

    found the fault in the dry fan and resoldered the spade so the fan is now okay and running.
    The cut out was .07M ohm between the two connections. I shorted it out and all the machine would do was continually click round and round. I disconnected both connections to open circuit and the fan came ON but no heat.
    Can anyone confirm if the component near the heater is a cutout or nct. I suspect that here is another fault.

    May 21, 2013 at 2:02 pm in reply to: inesit wd10 not heating #395168
    kevinlewis
    Participant

    Re: inesit wd10 not heating

    is that what it was fixed next to the heater.it did have a resistance but not open circuited so i thought that it was an nct. probably it is a saftey cut out. i should have checked. Thanks for that.

    March 20, 2013 at 10:04 am in reply to: Neff dishwasher switch bank required #392293
    kevinlewis
    Participant

    Re: Neff dishwasher switch bank required

    yes thankyou, but have you got one? They are no longer avaiable

    March 19, 2013 at 10:21 am in reply to: Neff dishwasher switch bank required #392291
    kevinlewis
    Participant

    Re: Neff dishwasher switch bank required

    the e nr number is S4133w0gb/20 fd 7602.
    the customer says that its a 4 button switchbank. she has already got her own engineer to fit it, if the part can be sourced.

    March 2, 2013 at 5:04 pm in reply to: BEKO FRIDGEFREEZER A190W #387686
    kevinlewis
    Participant

    Re: BEKO FRIDGEFREEZER A190W

    it only required the fan. It took about 20 min before the sensor signaled the pcb to start it up.

    March 2, 2013 at 4:58 pm in reply to: meile T234c #390224
    kevinlewis
    Participant

    Re: meile T234c

    It was the door switch. job now sorted.
    the pcb part number 6190985. exchange price of £121 plus vat. it has EPWL 300 KD stamped on it. QER have said that they have done successful repairs to this pcb in the past.

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 152 total)
1 2 3 4 … 9 10 11