Kirk

Forum Replies Created

Viewing 15 posts - 196 through 210 (of 250 total)
1 2 3 … 13 14 15 16 17
  • Author
    Posts
  • July 26, 2005 at 9:21 pm in reply to: EAC Rumours #143243
    Kirk
    Participant

    Re: EAC Rumours

    I heard a similar story and that it was Brandt that caused the problem, due to there being new owners they were being very diligent in trying to recoup some cash flow, but also there is something going on with Stoves all their eng are at a meeting next week! with the cross training something is afoot.

    Kirk

    July 23, 2005 at 1:29 pm in reply to: Dedietrich Refrigerator Stat #142939
    Kirk
    Participant

    Re: Dedietrich Refrigerator Stat

    Thanks Dave carry all so won’t be a problem, trouble is with this make not knowing the model numbers.

    Kirk

    June 24, 2005 at 9:45 pm in reply to: Comet Service Centres #106185
    Kirk
    Participant

    Re: Comet Service Centres

    They have over the years done different items for hotel chains Vids TVs Fridges etc.

    Kirk

    June 8, 2005 at 9:18 pm in reply to: Miele wont start #137057
    Kirk
    Participant

    Re: Miele wont start

    Thanks for your help Kirk

    May 31, 2005 at 9:45 pm in reply to: KENWOOD KDW12SS Dishwasher #136577
    Kirk
    Participant

    Re: KENWOOD KDW12SS Dishwasher

    One of the common faults is water leaking from the door ? and going into sump which puts the machine in anti flood mode, so untill water is removed or dries out it stays in the fault mode. I have come across some of the cheap dishwasher powders causing this.
    I do dread going to them. Kirk

    May 24, 2005 at 9:25 pm in reply to: BOSCH d/w SGS5338L #135768
    Kirk
    Participant

    Re: BOSCH d/w SGS5338L

    Thanks Norman

    May 6, 2005 at 10:15 pm in reply to: Can dishwashers be fed with hot water rather than cold? #133927
    Kirk
    Participant

    Re: Can dishwashers be fed with hot water rather than cold?

    Also if your Hot water is to hot it will turn the softener crystals to jelly and stop it working. Kirk

    March 29, 2005 at 8:10 pm in reply to: Blomberg 1501 AAA Fault’s #130009
    Kirk
    Participant

    Re: Blomberg 1501 AAA Fault’s

    A thin long cable tie fits into the jets nicely and does the job well.

    Kirk

    March 21, 2005 at 10:01 pm in reply to: What is the most useful tool in your toolbox? #107178
    Kirk
    Participant

    Re: What is the most useful tool in your toolbox?

    Very similar to the ones we used on the old Zanussi spyder the three inner bolts.

    Kirk

    March 17, 2005 at 9:31 pm in reply to: AEG E10 Fault #129169
    Kirk
    Participant

    Re: AEG E10 Fault

    Turned out to have a knackered compressor. Still don’t Know E10 fault though.

    Kirk

    March 17, 2005 at 8:56 am in reply to: AEG E10 Fault #129168
    Kirk
    Participant

    Re: AEG E10 Fault

    It would seem to be an electrolux unit and all my codes on fridges has disappeared.

    Kirk

    March 16, 2005 at 10:17 pm in reply to: AEG E10 Fault #129166
    Kirk
    Participant

    Re: AEG E10 Fault

    Thanks Simon for the offer but the customer couldn’t find it, I was hoping there would be just one set how stupid!

    Thanks Kirk.

    March 11, 2005 at 8:39 pm in reply to: Bosch TD WTE 5820GB #128447
    Kirk
    Participant

    Re: Bosch TD WTE 5820GB

    Thanks Martin I will give it a try Mon.

    Kirk

    March 8, 2005 at 9:59 pm in reply to: Hotpoint WMA31P motor #128091
    Kirk
    Participant

    Re: Hotpoint WMA31P motor

    Firstly you must not connect the motor to direct mains this a workshop test in a vice and only proves the armature and brushes ok or faulty.

    There are two different motors used one has the brushes either side the other are top and bottom.

    Did you put the motor plug in correctly as it can fit either way and must be fitted with the wires facing up. If you fitted it wrongly it will have blown the module so no motor action.

    You sound very competant with electrics but I feel you need to call in someone to save you money in the long run.

    Kirk

    February 25, 2005 at 7:43 pm in reply to: Liebherr fridge door. #127044
    Kirk
    Participant

    Re: Liebherr fridge door.

    it is very rare for the fault to be the fridge hinges, it is nearly always the external door sliders catching.

    Kirk

  • Author
    Posts
Viewing 15 posts - 196 through 210 (of 250 total)
1 2 3 … 13 14 15 16 17