laurenceuk

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 436 total)
  • Author
    Posts
  • in reply to: Where Can I Source Tecnik Parts Please? #215325
    laurenceuk
    Participant

    Re: Where Can I Source Tecnik Parts Please?

    Hi Andy,

    Thanks

    The model is listed on the first post TKL9290 W/D

    Thanks again

    Laurence

    laurenceuk
    Participant

    Re: Zanussi D/W DE744 Water Valve Locks Out With Pressure Ch

    Thanks Cliff – received ok.

    Very much appreciated

    Laurence

    in reply to: Zanussi FLE 1015W #211870
    laurenceuk
    Participant

    Re: Zanussi FLE 1015W

    Connect price:

    £18.83+vat
    for 2 = £15.78+vat each

    Laurence

    in reply to: Zanussi FLE 1015W #211867
    laurenceuk
    Participant

    Re: Zanussi FLE 1015W

    Oops! forgot to add the Connections part No 5031689792417

    Laurence

    in reply to: Zanussi FLE 1015W #211866
    laurenceuk
    Participant

    Re: Zanussi FLE 1015W

    Those I changed had handles Jim.

    Laurence

    in reply to: Zanussi FLE 1015W #211863
    laurenceuk
    Participant

    Re: Zanussi FLE 1015W

    Hi Jim,

    A quick look on Connections seems to show this as a solenoid interlock.

    I have changed two of these for making a clicking noise.

    Laurence

    in reply to: Test Procedure for a Hotpoint WMA63 Needed #211323
    laurenceuk
    Participant

    Re: Test Procedure for a Hotpoint WMA63 Needed

    Thanks everyone for your input.

    I put the machine through a test procedure and it came up with E30 –
    motor tacho failure.

    I have a circuit through the tacho coil, the tacho magnet is secure on the
    shaft and the plug wiring is ok.

    Because the chaffed motor (armature) lead and heater lead where
    adjacent to each other in the loom (bare conductors exposed on both)
    and that they may have touched and damaged the chopper board, plus
    the fact that the motor leads also enter this board then I am making the
    assumption that the chopper board is the culprit 🙁 – unless someone
    can assure me differently.

    Thanks again for your help.

    Laurence

    in reply to: Public Liability Ins Minimum #211103
    laurenceuk
    Participant

    Re: Public Liability Ins Minimum

    Thanks Martin

    in reply to: I Need a Diplomat Cooker Stat Pt No #210452
    laurenceuk
    Participant

    Re: I Need a Diplomat Cooker Stat Pt No

    Thanks Ken – on order with M/Part.

    Laurence

    in reply to: Zanussi Washer/drier ZWD1680 Probs After Conifuring? #209389
    laurenceuk
    Participant

    Re: Zanussi Washer/drier ZWD1680 Probs After Conifuring?

    Hi David,

    No it did not pump before filling for those few seconds.

    The diagnostic sequence seemed eratic – it did not seem to follow what I was reading from the manual.

    I will do as you advise

    Thanks

    Laurence

    in reply to: Bosch D/washer SGS5358GB/17 Programme Times Have Changed? #207574
    laurenceuk
    Participant

    Re: Bosch D/washer SGS5358GB/17 Programme Times Have Changed

    Hi,

    This was a model that took the time of its present wash from the previous wash.

    The initial complaint was that it would not fill so machine obviously took the time for the next wash from when the machine was switched off.

    The original fault has not re-occured and the times are now back to normal.

    Thanks for everyones input.

    Laurence

    in reply to: Bosch T/dryer WTL5100GB/11 Does This Point to the Timer? #207570
    laurenceuk
    Participant

    Re: Bosch T/dryer WTL5100GB/11 Does This Point to the Timer?

    A new timer fixed the problem.

    Thanks for all your help

    Laurence

    laurenceuk
    Participant

    Re: Bosch D/washer SGS5358GB/17 Programme Times Have Changed

    Thanks Gegsy – for both replies.

    Laurence

    in reply to: Dei Deitrich Cooker – Hinge Identification – See Photo`s #205104
    laurenceuk
    Participant

    Re: Dei Deitrich Cooker – Hinge Identification – See Photo`s

    Thanks Martin,

    Just gave them a quick call but they don`t supply spares for machines
    over 15 years old. This one is nearer 20 years old 🙁 . They don`t
    recognise the model number format.

    Laurence

    in reply to: Dei Deitrich Cooker – Hinge Identification – See Photo`s #205102
    laurenceuk
    Participant

    Re: Dei Deitrich Cooker – Hinge Identification – See Photo`s

    Hi Goose,

    Sorry for the slow reply – went down with some horrible sickness and
    `the other thing 😯 ` (you might be reading this at breakfast).

    The link just goes to `page cannot be found` and I can`t find Atoz Sales anywhere.

    But thanks for trying.

    Do you know any supplyers who do Dei Deitrich parts?

    Laurence

Viewing 15 posts - 226 through 240 (of 436 total)