[maltheviking]

Re: Hotpoint WT960P

Thanks guys, I wish Connect and Masterpart would get their act together and give the correct advice , it just threw me when I read it.

I had thought of EMW 😉

[maltheviking]

Re: Miele Dishwasher G675 SCi-2

Thanks clayside

[maltheviking]

Re: Hotpoint SE89PGX single oven

I have a recollection this oven is one of the Ariston Forno’s yes/no
The last one of these I had cutting out was down to a faulty potentiometer (one of the controls) worth trying as its cheaper than the PCB/timer

[maltheviking]

Re: Hotpoint Freezer FZ150G

Thanks Bob.
That’s the kit I have. Does the new board come with a diagram of where to connect the LEA?

[maltheviking]

Re: Siemens D/W SN25M830UK/01

timdowning wrote:Can someone kindly send me the tech info on this machine.
Diverter timer getting hot but not diverting, stuck in top spray arm mode.
Would be nice to see how these things come apart without me jabbing and prising too much.
Ta.

PM me with your email

[maltheviking]

Re: WIB111

BobHope wrote:that com code is not listed if its 46470 then its part no C00085194.

Bob.
Probably is that code, I was trying to read it with a torch in a blacked out garage! That part no is the standard one that I quoted which is longer than the one on this machine. 😕

[maltheviking]

Re: Zanussi Jetstream+ ZWF16581W

appliancesquad wrote:
The one certain lesson I learnt from my training course is that I have it all to learn!

Any advice accepted and thanks again.
How long was the course?, it does not supprise me that they take your money and dump you out on the street. I would have thought they should have at least helped you with, names of parts suppliers, which companies provide technicle backup (few and far between) where you can access information,etc.
I presume they did train you to use “Meggers,loop testers and multimeters”?
BTW you still need to PM me with your email address 😉

[maltheviking]

Re: eSpares Bought By Connect?

kwatt wrote:I dont’ think I’ll worry too much about that. 😉

However word is coming through that the OFT have shown an interest in the deal and I’m waiting on more information to compile a news story on the subject.

K.
Funny how the OFT gets to hear about these things Ken :rolls:
Prices might be interesting

[maltheviking]

Re: Zanussi Jetstream+ ZWF16581W

Hi Mate welcome to the mad house 😉
I presume because you are new to this you will not be aware that there is a diagnostics program for Zanies? I you care to PM me with your email I might be able to help with some goodies.
By the way you need to test the valve with a meter to see if the coils OK

[maltheviking]

Re: Stopped clock on Tricity President 2552

Hi amtrakuk
I think you may find that most parts are obsolite for this model,sorry

[maltheviking]

Re: Beko fridge freeze recall

Not be long before compensation claims come flooding in. I hear Scousers are advertising to take your Beko fridge off you, free of charge

[maltheviking]

Re: Beko fridge freeze recall

Masterpart were sending out details of the updated timer. Can I suggest that anyone who hasnt got the update either contact Mpart or Beko. I would post it here but I might be contravening some of UKWG policies :rolls:
Sod it it’s here, better be safe than sorry, I think Beko should be thanking us for looking after their interests. Sorry Ken if I have over stepped, I will greatfully accept slapt wrists :rolls: http://www.masterpart.com/Beko_Technica … 90100.html

By the way check the date of the update 😐

[maltheviking]

Re: WD12x Indesit washer/dryer

scientist wrote:Gotcha….EMW?? can you fill me in?

You must be one of the only ones on this site who doesnt know about EMW 😆 here you go mate, Google searched by the way :rolls:
http://www.emwelec.co.uk/

[maltheviking]

Re: Hotpoint sump hose 161032

Cheers Jim
In all the years I have never been without a 161032 in my van, I had an idea the newer ones would fit, Ill get one ordered

[maltheviking]

Re: Hotpoint sump hose 161032

Thanks Jim
Have a look for me please when you can

Mal

[Author]

Posts