Forum Replies Created
-
Posts
-
Re: Getting the belt on the tension pulley – Hpt condenser d
iadom wrote:On the WMA washing machine, I put the belt on the motor pulley, then fix the belt to the drum pulley with a strong plastic bag tie, then walk the belt onto the drum pulley.
How on earth do you do that when you can’t even access the pulley from the back to tie the tie even…?
Martin
Re: What washer for up to £300?
CBestwick wrote:as if to suggest the Classixx range isn’t?
You get what you pay for but the Classixx range is fine, just built more on a budget to compete with others with a slower spin speed. 😉
Martin
P.S. Turn the light ( 💡 ) up on your website will ya, can’t read the wording? 😆
Re: Getting the belt on the tension pulley – Hpt condenser d
Andy,
Hotpoint produce the 2 different sizes of special tool, the larger one for fitting WMA belts the smaller for tumble dryers. (I don’t recall the part numbers though? – I’m sure someone can though!)
Martin
Re: Common Sense
Penguin45 wrote:Linford? Martins got a pet tortoise? :rotl:
How could anyone wish harm to my little randy racing rock?
As for our Finnish friend?…He is awaiting the bearing seal and much more will be added to that thread no doubt in the coming weeks, loads of photo’s I expect too :rotl:
Linford is now under 24 hour surveillance, just in case :martin:
Kevin?….I’ve got a nice machine for you…Oh yes 8)
Martin
kwatt wrote:Your a nutter Martin! :rotfl:
Seems the world is full of us too, there’s poor old Pat-UK suffering some prat customer over a ‘no show’, Yurtesen with his friggin’ washing machine that should be scrapped (Oh! just occurred to me, my mother always told me when I was Kens age..(just kiddin’) ……… “Never accept free CANDY from a stranger!”) :lesson:
…..and then!..>What are we left with eh???
GOATBOY and ALEXA………….!!!! :rotfl:
This site is full of nutters :rotl:
Martin
Re: Common Sense
17:19
Jesus he’s back….!!
Yes, that machine looks quite fine also. No problems I think I shouldnt complain about a free washing machine :p
But I hope this doesnt cost you anything. I mean it is for sure that you wont get anything but popularity in forum from this… I mean, I would have wanted to help you out some way also but I am just a bored network engineer
Evren
😕
Re: Common Sense
Dave_Conway wrote:Why are you continuing with the offer ???? :con:
I didn’t realise you told him I would not be supplying him, ah! that’s why he went off site then so readily…shame eh?….. 8)
I will just have to save my Euro’s for my hols instead….Going to Finland for a wedding later this month too, perhaps Eversen will be there?
:rotl:
Martin
Re: Common Sense
I have noticed that Yurtesen has been on UKW all the while whilst all this banter has been going on. I switched on around 8 this morning…he was there…I have had 4 pm’s with him about supplying a new machine (even showed him a picture of the one I was to supply :tup: )
I’ve been off site (grafting an’ all that)..got back around 3:30…HE STILL THERE!…another pm for me asking…”I would prefer a front loader please?”…I told him I could only supply a top loader, sorry 🙁
…..he’s now gone off site (in a huff maybe?)
Martin
Re: Cost of dealing with the public
Not a leg to stand on she hasn’t Pat, no court in the land would uphold any action against you. Your actions where fully substantiated, your explanations fully justifyable. Your motives and concerns for the well being of your ‘customer’ where never at any stage in jeopardy. The timing of the claim against you also unreasonable and premature from the outset.
We will back you to the hilt on this in whatever way we can! 👿
Martin
Re: Electrolux seems possessed!!!
Mark,
No it is not possesed but rather in need of attention to the motor thats all. Probably needs a new set of brushes and the Tacho checking out :tup:
Also the manifold needs close attention etc etc. Not a costly exercise at all but one that requires expert attention nonetheless. Not a DIY job!!!
We may have someone on this site local to you that can sort it? Try this link:-
Repairs@Martin
Re: Common Sense
Dave_Conway wrote:Don’t even go there please, he’s going with the bearing replacement, leave it at that.
:worthy: :duck:
Whatever you say Dave….. but be prepaired to hear much more from our ‘$hit in $uomi’ when he gets the seal in the post :rotfl:
:rotl: :rotl: :rotl:Keep smilin’
Martin
Re: Common Sense
Penguin45 wrote:In the mean time, let’s get the provisional wing of UKW to fit a tracker on Martins van and see where he goes over the next few weeks.
:rotl:
I am more than pi$$ed off with Evren Yurtesen’s ( alias Minna Kelloniemi ) postings. And when Dave told me he lived in Finland it was my chance to offer a new machine (see link below) just to shut him up 😈
http://tuotteet.expert.fi/product.php?id=479I will get this machine delivered to his place via my mate Markuu Keltto having first transferred the money to his bankers. But I half suspect (judging by the addition ramblings since my Finnish post – Markuu translated it for me by the way as no way do I speak that weird lingo -) That he is STILL carrying on trying to get the race off 🙁
They are a funny lot in Finland after all :lol2:
….and NO Chris!…I really haven’t fallen out of my tree…honest!
Martin
Re: candy alise 105 changing bearings
Rakas Evren,
Tämä tarjous on aito ja ystäväni suomessa ottaa sinuun yhteyttä jos sinä annat minulle osoitetietosi. Olen pahoillani ettet voi korjata vanhaa konettasi mutta voin toimittaa sinulle kivan uuden jos haluat?
Parhain terveisin
Martin
Re: candy alise 105 changing bearings
iadom wrote: If I strip the gearbox down and send you the pictures of the faulty cogs will you be able to find the part numbers and send them to me.
‘Off topic’ and I will laugh along with you at this, BUT on this topic right now?….I choose not to OK? 👿
Martin
Re: candy alise 105 changing bearings
yurtesen wrote:
I am sure you understand me being a little bit skeptical. So, you will pay for the machine also or only buy it? 🙂 There must be some word trick here really.No trick…I very much enjoyed your postings…no word tricks either….Give me the details I ask of you and I will supply you a new machine, delivered to your door there in Finland
Anticipating your next question…WHY?? Not your problem, only my problem just to show these ‘colleagues’ of mine on this website that everything I say on here is true, with no exception. This is my perfect opportunity to cast aside their doubts 😉
Just go along with what I ask and NEVER LOOK A GIFT HORSE IN THE MOUTH as we say here in the UK.
My contribution to this site is NOT a joke in spite of this characterisation ( :martin: )
Are you up for it Mr Evran Yurtesen?
Hey! Hey!
Martin
