[mike412]

Re: Bosch WFR2460GB/01 W/M

Hi.

I dont understand the last post but…

I have got this job booked for friday. Thinking about the problem, I am not sure that I made the fault completely clear in my 1st post.
The display “sort of” illuminates but does not dislay any info, and if you “start” the machine nothing happens. If you leave the machine in limbo for half an hour the display comes on , you can hit the start button and use the machine as normal. If it was a problem with the display board, would you not be immediately able to use the machine, but for lack of a display, not know exactly what it was doing?.

Comments Welcome ,

Thanks in anticipation,

Mike

[mike412]

Re: Bosch WFR2460GB/01 W/M

Thanks for that Martin. Will give it a Bash next week and post conclusion.

Cheers,
Mike

[mike412]

Re: De Dietrich RG4150U6/01 Fridge

Thanks Bazza.

armed with gen part number, I can shop around better.

Regards, Mike

[mike412]

Re: Hotpoint WF541 Harness

Thanks Jim,

You are my Hero!

Mike

[mike412]

Re: 6.2kohm resistors

Hi.

I use Farnell for these.

Part number 747-865 6.8k 7w. Cheap as chips.

http://www.farnell.com/uk 0870 1200 200

Mike

[mike412]

Re: Hotpoint WD71

I ommitted to say that on pump and spin it was still heating. Just thought I would add this little snippet of info to bring this post back up to the top of the pile!.

Any assistance much appreciated.

Regards,
Mike

[mike412]

Re: Hotpoint WD71

Hi , Thanks for that.

This was my first thought , but the heater meggers up fine. It will probably end up being something silly.

Cheers, Mike.

[mike412]

Re: Creda 49702 dble ovn fr. stndng ckr circuit/wiring diagr

Hi Mike.

I dont have a diagram for this exact model, but I do have one for a similar model which may help, just PM with email address.
If I recall this motor has a TOC built into the winding, also very particular about having its cooling fan on the end of the shaft.

Regards,

Mike.

[mike412]

Re: Hoover vision VHD 814 carbon brushes?

49000466 Is the part number for the Brush and Holder assy for the Sole Motor as fitted to various Hoover/Candy models. £23.00 pr from CDSL.

Hope this helps.

Regards, Mike

[mike412]

Re: electrolux tds wont work

Thanks for your help guys.

I should have mentioned that mine is a 2008 version.

I have passed your info on to my son who is a software engineer, I am sure that it will help.

I will “keep you posted”.

Regards Mike

[mike412]

Re: electrolux tds wont work

bazza500 wrote:I can`t get the electrolux tds UK 2006 V2 disc to work on my new laptop.

It seems to fully install but when I try and run it it says component “DBGRID32.OCX” or one of its dependencies not corectly registered: a file is missing or invalid.

My laptop is running Windows Vista, is this the problem?

Has anyone else come across this and if so did you find a fix?

Thanks, Bazza

I have exactly the same problem trying to get TDS to work on my new Sony laptop.
Could some kind person enlighten me please as to how to overcome this problem.

Regards,
Mike

[mike412]

Re: Tips or tricks replacing door seal on Ariston A1535

Please Cancel Last Message- Just found this post relating to a different model number but same problem.

What a pain in the butt, something to look forward to tomorrow.

Regards,
Mike.

[mike412]

Re: HOTPOINT WMA40 CONTROL BOARD

Thanks for your prompt reply Helo.

Looks like a shopping expedition to EMW then.

Many Thanks, Mike

[mike412]

Re: HOTPOINT WMA40 CONTROL BOARD

Thanks for that A1.

I only have the configuration sheet for the 1603557. This only goes up to WMA22. Can anyone help me out with the config data for WMA40?

Thanks in anticipation,
Regards,

Mike

[mike412]

Re: Enough to make you vomit…

Of course I did it, cant be squeamish in this trade. and, where theres muck theres money. (got a good tip if I recall).

Mike

[Author]

Posts