Minge

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 64 total)
1 2 3 4 5
  • Author
    Posts
  • November 16, 2008 at 4:18 pm in reply to: Zanussi DA6152 Dish washer #268598
    Minge
    Participant

    Re: Zanussi DA6152 Dish washer

    Possibly the anti flood kit is needed Kit “A” for N.S.
    5027 86 64-00/3 Kit “B” for “EVO”
    5027 86 65-00/0

    November 14, 2008 at 3:57 pm in reply to: Hotpoint Fridge Freezer FF200E #268323
    Minge
    Participant

    Re: Hotpoint Fridge Freezer FF200E

    Thanks guys – all working now! 😀

    November 3, 2008 at 12:31 am in reply to: Zanussi D/W Model ZDI6041 Prod 911841103 #267093
    Minge
    Participant

    Re: Zanussi D/W Model ZDI6041 Prod 911841103

    welcome buddy.

    November 3, 2008 at 12:14 am in reply to: KGN33V00GB/01 #267183
    Minge
    Participant

    Re: KGN33V00GB/01

    thanks pal. perhaps 3 days wasnt long enough????

    November 3, 2008 at 12:13 am in reply to: KGN33V00GB/01 #267179
    Minge
    Participant

    Re: KGN33V00GB/01

    Thanks guys. It has had no modification done to it as i am the first engineer she has ever called out. What does the mod consist of and where can i find the info on what/how to do it please? The appliance was definately defrosted fully when i returned so doubt it will be a blockage? Unsure if fan is running at mo tho… will check.

    October 30, 2008 at 11:49 pm in reply to: bosc sgf6902gb/22 – stuck on 1 minute #267047
    Minge
    Participant

    Re: bosc sgf6902gb/22 – stuck on 1 minute

    all that seems ok? Any other thoughts?

    October 30, 2008 at 11:48 pm in reply to: Zanussi ZWF1640W #266389
    Minge
    Participant

    Re: Zanussi ZWF1640W

    If it has a thin blue cable harness between the display and main module it is quite common for this to be at fault. You will probably find the display was going on and off intermittantly previously and was struggling to start?

    October 30, 2008 at 11:45 pm in reply to: Zanussi W/D – Prob #267096
    Minge
    Participant

    Re: Zanussi W/D – Prob

    E10 is the dryer inlet valve fault. More than likely the ‘3 valve’ type in which case is normally the green one but you can by the complete valve assembly.

    October 30, 2008 at 11:43 pm in reply to: Zanussi D/W Model ZDI6041 Prod 911841103 #267089
    Minge
    Participant

    Re: Zanussi D/W Model ZDI6041 Prod 911841103

    if the water is clean i doubt it will be a syphoning issue. Perhaps an inlet valve bypass???

    October 30, 2008 at 10:30 am in reply to: LEISURE RM10FRS – 04 100235 08 – RIGHT SIDE NOT WORKING????? #266818
    Minge
    Participant

    Re: LEISURE RM10FRS – 04 100235 08 – RIGHT SIDE NOT WORKING?

    Thanks guys but yeah, on the right hand oven the thermal fuse is ok but still dead???? Also would the thermal fuse cause the ignition switch for hobs to not work? Or the warmer plate? Any other ideas?

    :rolls: ❓

    October 21, 2008 at 5:57 pm in reply to: SMEG DISHWASHER #265218
    Minge
    Participant

    Re: SMEG DISHWASHER

    LOL

    Sorry mate. It is a DW1612C

    October 5, 2008 at 11:25 pm in reply to: baumatic bdw13 – bottomspray arm not rotating #263367
    Minge
    Participant

    Re: baumatic bdw13 – bottomspray arm not rotating

    lol
    thanks again chris.

    October 5, 2008 at 11:07 pm in reply to: baumatic bdw13 – bottomspray arm not rotating #263365
    Minge
    Participant

    Re: baumatic bdw13 – bottomspray arm not rotating

    no the half load is not selected.. any other ideas please????

    October 5, 2008 at 11:06 pm in reply to: ARC7470 – DEAD #264353
    Minge
    Participant

    Re: ARC7470 – DEAD

    Thanks alot Chris!!

    Nice one, will give it a go.

    Cheers once again.

    October 5, 2008 at 11:03 pm in reply to: ARC7470 – DEAD #264351
    Minge
    Participant

    Re: ARC7470 – DEAD

    LOL
    I guess thats what it will be then.

    Is it the just the one pcb on this do you know? The one in the front panel at top?

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 64 total)
1 2 3 4 5