nigegt

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 420 total)
  • Author
    Posts
  • in reply to: no heat #420970
    nigegt
    Participant

    Re: no heat

    Poss dry joint on heater relay on PCB.

    in reply to: Beko DRCS76B #420969
    nigegt
    Participant

    Re: Beko DRCS76B

    Steam inside when cycle complete. And your first thought was mine too. Not long enough cycle for what she wants to dry.

    in reply to: Diplomat ADP 4610 double oven, #420047
    nigegt
    Participant

    Re: Diplomat ADP 4610 double oven,

    One of the elements on the appliance has an earth leakage fault most likely. You will need an insulation tester/megger to find out which.

    Nige

    in reply to: Confused Beko DWD4311 #419719
    nigegt
    Participant

    Re: Confused Beko DWD4311

    The main circuit board is only about £30. Must be worth that.

    in reply to: Beko Oven needs EXACT time ?!? #419036
    nigegt
    Participant

    Re: Beko Oven needs EXACT time ?!?

    You are setting in auto. even if you think you’re not. The oven will work (as has been said) regardless of what time it says and has no earthly way of determining actual time. Or if the manual setting wont work and you have to set through auto then the timer is faulty.

    in reply to: Ariston LSI 45/50 #419080
    nigegt
    Participant

    Re: Ariston LSI 45/50

    Broken wire in the door or earth fault on heater or wash motor would cause this. If you don’t have a megger then disconnect heater and see if you can select prog. then try same with wash motor to eliminate.

    Nige

    in reply to: samsung rsg5durs #419140
    nigegt
    Participant

    Re: samsung rsg5durs

    can you hear a clicking noise from the compressor every five mins or so? Could have ceased and wont show a fault code.

    in reply to: Beko CA5411FFW/2 Frost Free Fridge Freezer-Fridge is Frozen. #419156
    nigegt
    Participant

    Re: Beko CA5411FFW/2 Frost Free Fridge Freezer-Fridge is Fro

    There is a sensor buried in the back on the fridge evaporator which is most likely the fault you have. Cheap enough but a pain to dig it out from a diy point of view (means cutting into the insulation at the back) easier to get someone in to do it £60/£70 tops. Job done.

    Nige

    in reply to: Hoover DYN8164D Controller Board #418753
    nigegt
    Participant

    Re: Hoover DYN8164D Controller Board

    Yes the motor fault draws too much current and blows the rectifier.

    Nige

    in reply to: Bosch WWF1401 drum noise #418376
    nigegt
    Participant

    Re: Bosch WWF1401 drum noise

    Take the lid off and push the drum downwards and let go. If in comes back up and rests in a damped fashion then shocks are fine if it bounces or feels un-damped then shocks are the issue.

    Nige

    in reply to: Whirlpool G2P DW1 #418683
    nigegt
    Participant

    Re: Whirlpool G2P DW1

    Put your ear to it and see if you can hear a faint hum. The wash motor may be the problem.

    Nige

    in reply to: Diplomat ADP 8332 faults mid cycle #418700
    nigegt
    Participant

    Re: Diplomat ADP 8332 faults mid cycle

    When it faults you need to count the number of flashes. This is the fault code.

    Broken door wiring is common on these so check here first regardless of the code.

    Nige

    in reply to: Fridge hinge for Neff integrated fridge #418749
    nigegt
    Participant

    Re: Fridge hinge for Neff integrated fridge

    Hinges come as a pair in a kit pt. no. 481147

    Nige

    in reply to: fridge frosting up but freezer struggles to get past -2 #418754
    nigegt
    Participant

    Re: fridge frosting up but freezer struggles to get past -2

    There is a valve which directs refrigerant to the fridge evap. This may be the issue.

    Nige

    in reply to: Hoover DYN8164D Controller Board #418750
    nigegt
    Participant

    Re: Hoover DYN8164D Controller Board

    Sounds like a motor fault. When it blows the board to bits it shows a door lock error just to keep you guessing! Had it on many occasions. Check the rectifier pcb also as it tends to affect that too.

    Nige

Viewing 15 posts - 31 through 45 (of 420 total)