oakleyjo

Forum Replies Created

Viewing 15 posts - 46 through 60 (of 65 total)
1 2 3 4 5
  • Author
    Posts
  • March 12, 2013 at 11:13 pm in reply to: Indesit WIE167UK Door Seal #391921
    oakleyjo
    Participant

    Re: Indesit WIE167UK Door Seal

    Excellent. Many thanks, Jon 😀

    March 11, 2013 at 6:41 pm in reply to: 2x Beko DC7041W – No Heat & No Drum rotation #391853
    oakleyjo
    Participant

    Re: 2x Beko DC7041W – No Heat & No Drum rotation

    Hi,

    Don’t know this machine, and others may have alternative ideas, but for the No Heat one I’d check for an open circuit thermostat in the heating circuit. For the Push to Start one it could be that the start windings in the motor itself have broken, should be able to check for open circuit coil.

    Jon

    March 11, 2013 at 2:27 pm in reply to: Hoover HNMF 2805 A80 #310785
    oakleyjo
    Participant

    Re: Hoover HNMF 2805 A80

    Hi,

    I know this is an old thread, but does anyone have the info on how to change the fridge sensor available? The machine I’m looking at is an L80 rather than an A80 but I assume the procedure would be pretty much the same?

    Thanks, Jon

    March 6, 2013 at 9:33 am in reply to: Hotpoint CTD00P Fans #292915
    oakleyjo
    Participant

    Re: Hotpoint CTD00P Fans

    Thanks for the info. The one I have is vibrating badly so I will replace it with the shorter one now I know it’s ok to do that.

    Thanks again,
    Jon

    March 5, 2013 at 2:40 pm in reply to: Hotpoint CTD00P Fans #292912
    oakleyjo
    Participant

    Re: Hotpoint CTD00P Fans

    Hi,

    I have a CTD00P in which the impeller fan is black and ~100mm in length. Can’t find anything matching that anywhere. Does anyone know where to get this length impeller fan, or whether the smaller fans that are available are a correct replacement? Service Ref number on the machine is 95313490000 608050037

    Thanks,
    Jon

    February 18, 2013 at 9:16 pm in reply to: Hotpoint BFI620 lights 2+3 flashing (timeout fill) #389881
    oakleyjo
    Participant

    Re: Hotpoint BFI620 lights 2+3 flashing (timeout fill)

    For the record I fitted the correct part number module today and everything now works fine 🙂

    Would’ve been right stumped on this one if I hadn’t asked !

    Many many thanks, Jon

    February 13, 2013 at 8:03 pm in reply to: Electrolux EWX14450W bearings/drum #390121
    oakleyjo
    Participant

    Re: Electrolux EWX14450W bearings/drum

    Ouch … thanks Martin!

    Cheers,
    Jon

    February 12, 2013 at 8:18 pm in reply to: whirlpool ADP44045WH (D/W) #389988
    oakleyjo
    Participant

    Re: whirlpool ADP44045WH (D/W)

    OWI is Optical Water Indicator in whirlpool language I believe. Otherwise known as the turbidity sensor.

    February 12, 2013 at 11:40 am in reply to: Hotpoint BFI620 lights 2+3 flashing (timeout fill) #389880
    oakleyjo
    Participant

    Re: Hotpoint BFI620 lights 2+3 flashing (timeout fill)

    Lights were flashing. Holding down the P key didn’t reset, just kept flashing. I’m confident everything was transferred across to the new module ok. I still have the original and there is nothing obvious still attached which I should have moved across.

    I’ll be going back to fit the correct module this time on Monday. Will be interesting to see if that clears the problem.

    Thanks, Jon

    February 11, 2013 at 7:14 pm in reply to: Hotpoint BFI620 lights 2+3 flashing (timeout fill) #389878
    oakleyjo
    Participant

    Re: Hotpoint BFI620 lights 2+3 flashing (timeout fill)

    Nope. Just double checked and it seems I’ve foolishly ordered and fitted the wrong one 🙁

    I’ll order the correct one and give it a try.

    Many thanks, Jon

    February 5, 2013 at 9:46 pm in reply to: CDA CI994 Washer Dryer Door Seal #389497
    oakleyjo
    Participant

    Re: CDA CI994 Washer Dryer Door Seal

    Great. Many thanks for your help 😀

    January 9, 2013 at 2:08 pm in reply to: Does Indesit WIDXL126UK have a sealed drum? #387560
    oakleyjo
    Participant

    Re: Does Indesit WIDXL126UK have a sealed drum?

    Thanks Martin. Appreciate the quick response. That’s just wahat I wanted to hear 😡

    January 4, 2013 at 9:27 am in reply to: F-Gas required for ANY fridge work? #387080
    oakleyjo
    Participant

    Re: F-Gas required for ANY fridge work?

    Many thanks for the clarification. Yes, I’m only doing domestic and wouldn’t touch the sealed refridgerant parts at the moment anyway. I have arranged for some training before I do that.

    Cheers, Jon

    December 20, 2012 at 11:16 am in reply to: CDA CI330 Washing Machine F8 fault code #386619
    oakleyjo
    Participant

    Re: CDA CI330 Washing Machine F8 fault code

    Thanks 😀

    December 19, 2012 at 6:50 pm in reply to: Ikea Whirlpool Nutid HB4IH Induction Hob numbers flashing #386568
    oakleyjo
    Participant

    Re: Ikea Whirlpool Nutid HB4IH Induction Hob numbers flashin

    Sorry, forgot to add that a pan was on the ring and it’s a suitable pan for induction. It’s one the owner has used for some time on this hob.

  • Author
    Posts
Viewing 15 posts - 46 through 60 (of 65 total)
1 2 3 4 5