Forum Replies Created
-
Posts
-
Re: Beko Wash Mach. WM7335 Anyone Had This Fault Before?..
Also, check the wiring between the tacho and the control board. I had this problem and the wire had broken off in the back of the motor connector.
Cheers, Jon
Re: Samsung fridge freezer
Hi Nige,
Please feel free to PM me with your email address and I will send you the information I have which should help.
Cheers, Jon
Re: Hotpoint Bearing Tool V2 Instructions
Thanks all for your help. The bearing tool I have is slightly different to the one in the instructions, I guess that’s because it’s a later V2 version. It doesn’t have a split ring, but has a variety of other adaptors. Certainly the instructions from Alan suggest how this one probably works so I’ll just have to give it a go. Looks like the instructions for the V2 kit come on a CD looking at the picture of the item on Masterpart.
Thanks again,
JonRe: Bosch/Neff Single Thermostat Fridge/Freezers
Hi Steve,
I haven’t checked the thermostat. The compressor is running and freezer compartment is very cold and quite frosted up. I would guess that if the thermostat was stuck on the fridge would also get too cold? The back wall is more frosted towards the top if I remember rightly, but I’m not 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure.
I’m actually looking at two of these which are identical integrated models installed side by side and both exhibiting the same symptoms. They’ve apparently been running for 2-3 years and never been defrosted which I can quite believe looking at the frost build up in the freezer compartments. I’ve checked that all the cupboard vents are clear and at the moment one of the machines is being defrosted to see if that helps. Not sure whether icing up is a problem with this type though as they have no fans or ducts to block?
Thanks,
JonRe: Bosch SGS5312GB/12 Dishwasher
Just to complete the thread. The problem was with the control board. One of the tracks was burnt off when I opened it up and took a look. Working fine with a new board fitted.
Re: SMEG DWI612C Dishwasher Door Lock
It is indeed broken lugs on the control panel which is the problem so that will need replacing. Is 763735661 the correct part number for the control panel facia with the lugs?
Thanks,
JonRe: SMEG DWI612C Dishwasher Door Lock
Thanks. Guess I better go take a look before ordering any parts !
Re: Bosch SGS5312GB/12 Dishwasher
Many thanks Martin. I will go and check all the connections before I suggest replacing the module.
Cheers, Jon
Re: Hotpoint DFW50 Dishwasher Eco Light flashing but not flo
Thanks Jim. PCB is ordered and fingers are crossed that it cures the problem 😉 I’ll post the result.
Cheers,
JonRe: samsung side by side fridge freezer srs2028css
Possibly the compressor overheating and shutting down. Check that all the air vents at the rear/bottom of the machine are clear and that the condenser and cooling fan isn’t all clogged up with dust. If it works for a short while after a defrost that may be because the compressor has had time to cool itself and will run for a little while before overheating again.
Re: Zanussi ZDF2020 Dishwasher Not Filling
May be possible, but I’m afraid I don’t know how to get to diagnostics mode on this machine 🙁
Re: Hotpoint WM64P motor
Many thanks Jim, that’s a really helpful answer. Hadn’t even considered you could change the armature. Much appreciated.
Cheers, Jon
Re: Smeg suk91mfx5
Hi Tim,
Very confusing, and I’m not an expert so I’m not sure I can help much, but just in case you weren’t aware there is a small (but quite expensive) PCB in these ovens (bottom r/h side looking from the back) which switches the neutral side of the element pairs, l/h fan and base, r/h fan and grill. Could be a red herring, but perhaps worth checking if the relays on the board are stuck ?
Jon
