Forum Replies Created
-
Posts
-
Re: Anguis in herba
If he is from Leeds, I haven’t a clue who he is……
Like paragraphs, but not capitals and punctuation.
Chris.
Re: Electrolux Aqualux EW1200i – not draining during dry cyc
Drain hose crushed by the tight installation is always a good bet, as is the sink coupling clogging up where the drain hose joins in. If it’s hanging down all sorts of things from the sink can accumulate.
Regards,
Penguin45.Re: AEG OKO LAVAMAT 16800
You will observe a centre seam down the casing sides – the rear half can be removed by undoing 4 or 5 screws around the lower casing and four under the lid.
Power off if removing any panel.
Regards,
Penguin45.Re: Parnall Easy Dry Compact 37358
Jackson bought Parnell. Creda bought Jackson. Hotpoint bought Creda. Indesit bought Hotpoint. Then the world as we knew it ended.
Penguin45.
Re: Ariston ADL120FR Washing mach bearing kit-determining mo
Your third picture shows the worst – the shaft is stepped in and is now undersized where the bearing will sit. It will therefore be loose inside the new bearing, so the seal won’t work.
Unlucky…….
Regards,
Penguin45.Re: ZANUSSI WASHING MACHINE MODEL ZWF1221W
Have the polystyrene packing pieces been removed from the sides of the drum? Tip the machine back and see if there are two polythene bag ends hanging down.
Regards,
Penguin45.Re: Ariston ADL120FR Washing mach bearing kit-determining mo
It’s an RH thread. Most of us use heavy duty automotive torx bits for the job – the extended ones are useful as they allow you to give the bolt head a good clout, helping to shock it free. It’s Loctited on as well as being tight.
Good Luck,
Penguin45.Re: Anguis in herba
Oh, and they’re all going to be on in the morning wondering why the time is wrong………..
Chris.Re: Anguis in herba
Not sure about the need for all the subterfuge. I have a suspicion that the odd Mods Forum title rolling on the XML is no bad thing – the thin white(goods) line is doing its job. Maybe we are watching you! Keeps ’em all on their toes. 😀
Chris.
Re: Error code 9 on SmartDrive 703
F+P only offer schematics for the overall machine – there are not layouts for the actual control boards. What I can tell you is that it’s a DC, 3 phase motor with 42 poles. By selecting and ganging together different combinations of poles, the different speeds for the machine are achieved.
HTH,
Penguin45.Re: F&P GW601 pausing on spin
This is the “How long is a piece of string” question……..
Water level control faulty.
Dodgy wiring.
Bowl not re-engaging.
Pump fault.
Rotor sensor fault.
Motor fault.
Motor board faulty.
Lid switch faulty.
OOB switch faulty.Want any more?
Penguin45.
Re: Test Modes GW601
You can test the balance and lid switches, the water valves and the pump.
Enter diagnostics (wash temp down, power on).
Lid switch ok – 12 minute light should be on.
Manually activate OOB switch – 6 minute light should come on.
Pump – pressing Regular Cycle will start or stop the pump.
Wash temp down will operate the cold valve.
Wash temp up will operate the hot valve.There is no test function for the motor.
Regards,
Penguin45.Re: ZAN-ZCGHL55XN
Penguin45 wrote:Asked himself to ask around, but he found this then went to sleep.
Oi! I did bloody well to get that far…… Who else was still out fixing at 5pm on a Saturday?
Gonna change that damn password…….
😀
Penguin45.
