Penguin45

Forum Replies Created

Viewing 15 posts - 1,861 through 1,875 (of 19,678 total)
1 2 3 … 124 125 126 … 1,310 1,311 1,312
  • Author
    Posts
  • October 24, 2009 at 4:20 pm in reply to: My faithful 10 year Siemens SE56590GB/07 is not well! #300256
    Penguin45
    Participant

    Re: My faithful 10 year Siemens SE56590GB/07 is not well!

    Remove plug, lid and r/h side panel. Suppressor is in the bottom rear corner revealed – inside where the mains cable comes in. If it has blown there is usually visible evidence.

    Replacement part HERE.

    Penguin45.

    October 24, 2009 at 4:07 pm in reply to: ignis 348 motor and press switch #300336
    Penguin45
    Participant

    Re: ignis 348 motor and press switch

    ADL348? SWITCH.

    Chris.

    October 23, 2009 at 11:37 pm in reply to: Tom Tom gone. #299035
    Penguin45
    Participant

    Re: Tom Tom gone.

    eastlmark wrote:think you will find its an Renault 12

    😳 It is, isn’t it….. 😳

    Chris.

    October 23, 2009 at 11:35 pm in reply to: Flavel Aspen 100 #300296
    Penguin45
    Participant

    Re: Flavel Aspen 100

    Not enough to go on with the reference given. If it’s dead on one side only, I’d be looking for a microtemp or thermal cut-out in the live feed for the side that’s failed.

    Chris.

    October 23, 2009 at 11:30 pm in reply to: Smeg slimline #300294
    Penguin45
    Participant

    Re: Smeg slimline

    Flood protection activated.

    Standard leak is from the joint between the upper and lower fill matrices; obviously usual culprits can apply – circulation motor, over-fill, furry creatures nibbling things…..

    Chris.

    October 23, 2009 at 11:26 pm in reply to: finluxwashers #300292
    Penguin45
    Participant

    Re: finluxwashers

    Look likes Vestel product to me – you’ll be fine.

    PICCIES.

    Chris.

    October 23, 2009 at 7:37 pm in reply to: Belling IDW 603 E1 Low water pressure error #300259
    Penguin45
    Participant

    Re: Belling IDW 603 E1 Low water pressure error

    E1 means that an increase in water level has not been detected by the flow meter after 4 minutes. Is the machine actually filling?

    Penguin45.

    October 23, 2009 at 6:58 pm in reply to: Instruction manual – Electra WD1100 A #300221
    Penguin45
    Participant

    Re: Instruction manual – Electra WD1100 A

    Press “1/2 load” to make the dryer work. That’s the one most people need to know……

    Penguin45.

    October 23, 2009 at 6:53 pm in reply to: Tom Tom gone. #299033
    Penguin45
    Participant

    Re: Tom Tom gone.

    Ooh – isn’t that BirdieMango’s 99 in the backgorund?

    Chris.

    October 23, 2009 at 6:19 pm in reply to: Hoover VHD8122-80 Washer #300225
    Penguin45
    Participant

    Re: Hoover VHD8122-80 Washer

    KNOWN ERROR CODES P7.

    Chris.

    October 22, 2009 at 11:44 pm in reply to: closing down #221599
    Penguin45
    Participant

    Re: closing down

    Call in at Fisher and Paykel whilst your down there and see if you can bag an up-to-date tech disc with the washers on for me.

    Thanks,
    Chris.

    October 22, 2009 at 11:37 pm in reply to: Bosch WTF2806GB #300214
    Penguin45
    Participant

    Re: Bosch WTF2806GB

    WFT2806GB/13………

    PCB fault, sorry. 296713 – about £137.

    Chris.

    October 22, 2009 at 11:32 pm in reply to: fault code needed #300208
    Penguin45
    Participant

    Re: fault code needed

    Nuffin…….. anywhere……….

    What is it?

    Chris.

    October 22, 2009 at 11:25 pm in reply to: Hoover WPM110 WASHER #300196
    Penguin45
    Participant

    Re: Hoover WPM110 WASHER

    Try the timer/selector unit – 91201337. Dead cheap, very likely culprit.

    Chris.

    October 22, 2009 at 6:35 pm in reply to: Tom Tom gone. #299029
    Penguin45
    Participant

    Re: Tom Tom gone.

    That’s going to be wasted on your motorised tea tray, isn’t it, Mark? 😆

    :p45:

  • Author
    Posts
Viewing 15 posts - 1,861 through 1,875 (of 19,678 total)
1 2 3 … 124 125 126 … 1,310 1,311 1,312