Penguin45

Forum Replies Created

Viewing 15 posts - 1,876 through 1,890 (of 19,678 total)
1 2 3 … 125 126 127 … 1,310 1,311 1,312
  • Author
    Posts
  • October 22, 2009 at 6:32 pm in reply to: Whirlpool AWM 045 #300194
    Penguin45
    Participant

    Re: Whirlpool AWM 045

    That’ll be a knackered timer, then.

    Chris.

    October 22, 2009 at 6:29 pm in reply to: TEKA DW655FI VR01 flashing lights #300185
    Penguin45
    Participant

    Re: TEKA DW655FI VR01 flashing lights

    Door not detected shut if it’s a Fagor, flood protection activated if it’s a Chink.

    Chris.

    October 22, 2009 at 4:56 pm in reply to: hoover #300158
    Penguin45
    Participant

    Re: hoover

    Syphoning?

    Penguin45.

    October 22, 2009 at 4:52 pm in reply to: whirlpool pump #300166
    Penguin45
    Participant

    Re: whirlpool pump

    4819 360 18249

    Chris.

    October 22, 2009 at 4:47 pm in reply to: Smeg d/w DWF410SS #300162
    Penguin45
    Participant

    Re: Smeg d/w DWF410SS

    Repetative overfill. Can be p/sw; more likely pcb not turning off valve. Had one recently with blown suppressor, changed it and it all worked. Also had several where it was the pcb itself.

    Chris.

    October 22, 2009 at 8:35 am in reply to: F&P 603 error code 9 #300153
    Penguin45
    Participant

    Re: F&P 603 error code 9

    Size error – put ‘size AND error’ into Search for this Forum only – lots of info.

    Penguin45.

    October 21, 2009 at 11:37 pm in reply to: Scandinova Successor? #300125
    Penguin45
    Participant

    Re: Scandinova Successor?

    The old Scandinovas were built by Vestfrost in Denmark for Comet.

    Penguin45.

    October 21, 2009 at 11:31 pm in reply to: BoschSGS5302GB/07 #300108
    Penguin45
    Participant

    Re: BoschSGS5302GB/07

    Noise should be irrelevant to programme progress, unless the pump actually stops running. Burnt-out heater relay joint on pcb was an almost standard failure on these machines a few years back – no heat, machine never reaches temperature, programme won’t advance until temperature is reached…….

    Penguin45.

    October 21, 2009 at 11:26 pm in reply to: aeg wm #300138
    Penguin45
    Participant

    Re: aeg wm

    Not quite – the door will still lock, but the pcb won’t clock the fact.

    Chris.

    October 21, 2009 at 11:25 pm in reply to: Candy cdi 2012-80 #300033
    Penguin45
    Participant

    Re: Candy cdi 2012-80

    The pattern of the flashes will probably represent an error code.

    Chris.

    October 21, 2009 at 8:47 pm in reply to: Prima Double Gas Built-In Oven Model LPR 808 #300133
    Penguin45
    Participant

    Re: Prima Double Gas Built-In Oven Model LPR 808

    Glen Dimplex

    Chris.

    October 21, 2009 at 8:26 pm in reply to: Mods alert!! #300070
    Penguin45
    Participant

    Re: Mods alert!!

    All gone….

    :p45:

    October 21, 2009 at 6:55 pm in reply to: BoschSGS5302GB/07 #300106
    Penguin45
    Participant

    Re: BoschSGS5302GB/07

    Does it heat?

    Penguin45.

    October 21, 2009 at 6:48 pm in reply to: Ikea/Whirlpool DWF417 #300114
    Penguin45
    Participant

    Re: Ikea/Whirlpool DWF417

    Some sort of corruption issue then – dispenser coil and mains suppressor cause some weird faults.

    Chris.

    October 21, 2009 at 6:24 pm in reply to: Ikea/Whirlpool DWF417 #300112
    Penguin45
    Participant

    Re: Ikea/Whirlpool DWF417

    Three versions – one made by Bosch, two made by SMEG. 12nc number required really.

    Chris.

  • Author
    Posts
Viewing 15 posts - 1,876 through 1,890 (of 19,678 total)
1 2 3 … 125 126 127 … 1,310 1,311 1,312