pto

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 41 total)
  • Author
    Posts
  • in reply to: beko wmb10w bearing noisy ned advice or availabilty of manua #195686
    pto
    Participant

    beko wbm 10w £180 new
    come on,
    pity you Didn’t go over budget when you
    Bought this beko

    in reply to: Dodgy SAMSUNG SRL3928B #182357
    pto
    Participant

    Re: Dodgy SAMSUNG SRL3928B

    well i think it is a sensor in the freezer

    in reply to: BRANDT UPRIGHT FRIDGE / FREEZER – BREAKDOWN?!?! :-/ #192895
    pto
    Participant

    Re: BRANDT UPRIGHT FRIDGE / FREEZER – BREAKDOWN?!?! :-/

    I thought you only bought a Brandt once then you get wise
    And go for something better

    in reply to: Zanussi 1265 E20 error then display death #195061
    pto
    Participant

    Re: Zanussi 1265 E20 error then display death

    Put the machine on its side did we ?

    in reply to: Beware of Hoover 5year warranty Charges! #194221
    pto
    Participant

    Re: Beware of Hoover 5year warranty Charges!

    SerensTaid wrote:Many thanks Jim, I shall take your advice and call the firm out. I was doubtfull at first because they charge £89 plus for the call out and I am only on disability money with no work.
    Thank you once again.
    Dave.

    You knew the cost before you sent for them
    If it had been the tub you’d be happy
    It wasn’t but it still works so don’t complain
    And I won’t mention my last post that was deleted

    Jack

    in reply to: Vented vs consenser tumble dryers #193834
    pto
    Participant

    Re: Vented vs consenser tumble dryers

    kandl-appliancerepair wrote:
    If you had an airvented, you can buy a condensor box, which is just a plastic tub which the hose fits onto and empty that when it needs. But you will probably get quite a bit of fluff 😉

    which dont work and are a waste of time and money

    Jack

    in reply to: Bosch WFO2867GB Won’t stop filling! #192973
    pto
    Participant

    Re: Bosch WFO2867GB Won’t stop filling!

    A soldering iron works just fine on these

    in reply to: A BEST BUY budget washer? Advice welcome plz! #192183
    pto
    Participant

    Re: A BEST BUY budget washer? Advice welcome plz!

    Put in the bin and forget it they are the pits.
    Go get something decent. Spend more and get more,
    its the only way forward.

    in reply to: WMA34 Control Board config codes #192022
    pto
    Participant

    All the info comes with the board
    It has with the ones I’ve fitted

    in reply to: creda sensorcare belt fitment #191052
    pto
    Participant

    Re: creda sensorcare belt fitment

    You don’t fit the flat side to the drum, it’s the ribbed side to the drum.

    Hope the image helps…

    in reply to: creda sensorcare belt fitment #191049
    pto
    Participant

    Re: creda sensorcare belt fitment

    you dont have to remove both jockey wheels to fit a belt

    in reply to: creda sensorcare belt fitment #191047
    pto
    Participant

    Re: creda sensorcare belt fitment

    wrong belt ?

    in reply to: Zan F1045W only 1 selection works properly #189186
    pto
    Participant

    Re: Zan F1045W only 1 selection works properly

    Everything else fails to spin properly or something like that.

    well ?

    in reply to: Zanussi TC481W Tumble Dryer not Heating (not thermostat) #189062
    pto
    Participant

    Re: Zanussi TC481W Tumble Dryer not Heating (not thermostat)

    There are two stats on the element one of which is normally a manual reset
    But on the later ones it’s a one shot
    You get at it from the back of the dryer

    in reply to: Whirlpool American Fridge Freezer S20B-RWW20-A/G #188247
    pto
    Participant

    Re: Whirlpool American Fridge Freezer S20B-RWW20-A/G

    Tech-Whizz wrote:“In any event I am looking to replace the IDI RCV-002 Infra red ice detector board and looking for advice on how to prolong the life of this purchase.”

    Yes put it back on the rcd that will help prolong its life
    It must have had a earth fault. What a way to fix it

    Jack

Viewing 15 posts - 16 through 30 (of 41 total)