pup

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 464 total)
  • Author
    Posts
  • in reply to: Zanussi element change #316440
    pup
    Participant

    Re: Zanussi element change

    and me pls 😆

    in reply to: Samsung RS20CCMS help please #316408
    pup
    Participant

    Re: Samsung RS20CCMS help please

    r600 is your man on this

    in reply to: scrap prices #315342
    pup
    Participant

    Re: scrap prices

    dont leave anything outside put in van first, wastakeing machine back ,got out and got 2 men asking me if it was scrap 😥

    in reply to: hja 8703 #316316
    pup
    Participant

    Re: hja 8703

    bit of search shows candy / hoover part no 49011011 , :rolls:

    in reply to: white knight 767 cap change #316265
    pup
    Participant

    Re: white knight 767 cap change

    Penguin45 wrote:Back off, drum out. Enjoy. Charge lots.

    Chris.
    yes bit of fun one can have 😆

    in reply to: scrap prices #315333
    pup
    Participant

    Re: scrap prices

    aqualectric wrote:I’m always a little nervous about visiting the scrap yard regularly as they have cameras and take your details each time you weigh in. Is anyone else here bothered about the possibility (however remote) of a visit from DEFRA asking for proof of WEEE compliance or waste carrier’s licence?

    Steve. (probably worrying too much. :rolls: )
    do the scrap man have weee licence?

    in reply to: clarify wd12 indesit w dryer #315051
    pup
    Participant

    Re: clarify wd12 indesit w dryer

    see it easy when you take the top off 😆

    in reply to: scrap prices #315327
    pup
    Participant

    Re: scrap prices

    Penguin45 wrote:Stopper the drain hose and make sure it’s got lots of water in – it’s heavier when you go over the weigh bridge.

    Not that I’d ever condone such a practice, of course.

    :p45:good idea chris 😆 more beer money

    in reply to: scrap prices #315324
    pup
    Participant

    Re: scrap prices

    midlands 😆 found out if take motor out u get more for it as it copper

    in reply to: Hotpoint Smart Cards #315219
    pup
    Participant

    Re: Hotpoint Smart Cards

    Martin wrote:

    maltheviking wrote:
    Do you know there are some naughty people out there who have “cracked” more complicated TV satalite cards, naughty :rolls:

    Ah, but the thing there is that there’s a potential gain to be had by unscrupulous ‘Sky Crackers’ to do that. Whereas there is little or no point or interest in cracking anything Indesit…is there? 😕 we could use them in sky tv 😆

    in reply to: LG Bearing change advice #315313
    pup
    Participant

    Re: LG Bearing change advice

    i think it drum out job it been long time since i done one ,

    in reply to: indesit wdryer wd12 #314778
    pup
    Participant

    Re: indesit wdryer wd12

    adv wrote:aaahh which wire tho thers a lot of them 😆

    😳

    in reply to: candy f/f cic 320gb #314994
    pup
    Participant

    Re: candy f/f cic 320gb

    most time it pcb

    in reply to: Hotpoint 9604 Top Loader #314817
    pup
    Participant

    Re: Hotpoint 9604 Top Loader

    iadom wrote:Moved this topic to trade tech in case any other old gits have anything to add. 😉

    Young Jim. 🙂
    what do mean by old gits jim 😆

    in reply to: Lifting up washing machines to rear of van? #314784
    pup
    Participant

    Re: Lifting up washing machines to rear of van?

    squadman wrote:Yes exactly how I do it as well

    and me 😆

Viewing 15 posts - 76 through 90 (of 464 total)