Simon46

Forum Replies Created

Viewing 15 posts - 436 through 450 (of 2,216 total)
  • Author
    Posts
  • in reply to: Patching a holed tub #329027
    Simon46
    Participant

    Re: Patching a holed tub

    Ta Martin. Thats the stuff i will use. Many thanks.

    Simon

    in reply to: Whirlpool ARC7410 Fridge/Freezer – Not switching on?? #297399
    Simon46
    Participant

    Re: Whirlpool ARC7410 Fridge/Freezer – Not switching on??

    Did you ever manage to sort the problem out?

    Regards
    Simon

    in reply to: Bosch KGN34X60GB/01 Fridge/Freezer #241044
    Simon46
    Participant

    Re: Bosch KGN34X60GB/01 Fridge/Freezer

    Cheers Paul. An hour with hairdryer and still frozen!

    S.

    in reply to: Bosch KGN34X60GB/01 Fridge/Freezer #241042
    Simon46
    Participant

    Re: Bosch KGN34X60GB/01 Fridge/Freezer

    Is there a trick to getting the cover off underneath the evaporator. Have removed polystyrene and plastic sheet underneath but just wondering if ice is sticking it to rear.

    S.

    in reply to: Teknik TKL9060 washer with flooded base #232002
    Simon46
    Participant

    Re: Teknik TKL9060 washer with flooded base

    Replaced hose again from back of drum to the reservoir that is in line with the drain pump and waste hose on this bosch machine. What would happen if the hose was removed and the holes at back of drum and reservoir were sealed up?

    S.

    in reply to: Prima LPR926 oven clock #291825
    Simon46
    Participant

    Re: Prima LPR926 oven clock

    Clock buttons are now melted due to grillpan fire. What is part number for buttons please?

    S.

    Simon46
    Participant

    Re: Elba 692.1 single oven grill element and selector switch

    Thanks Steve. Will do.

    S.

    in reply to: Bosch KTR18P20GB/01 larder fridge freezing milk #320221
    Simon46
    Participant

    Re: Bosch KTR18P20GB/01 larder fridge freezing milk

    If it helps this larder fridge has the drawers that have runners that extend when pulling the drawers out.

    S.

    in reply to: re Baumatic BDW13 not heating #312710
    Simon46
    Participant

    Re: re Baumatic BDW13 not heating

    Will an indesit IDL500 protector fit this?

    S.

    in reply to: Whirlpool AWM 9000 doorseal fitting #318973
    Simon46
    Participant

    Re: Whirlpool AWM 9000 doorseal fitting

    Many thanks.

    Simon

    in reply to: VFU-65IT dishwasher door dropping down #316070
    Simon46
    Participant

    Re: VFU-65IT dishwasher door dropping down

    Now i remember. Many thanks K.

    S.

    in reply to: Engineering a solution #315120
    Simon46
    Participant

    Re: Engineering a solution

    Could imagine that in Evrens house 😆

    S.

    in reply to: A real pain in the neck. #314201
    Simon46
    Participant

    Re: A real pain in the neck.

    Hope you get better soon Jim. The only pain in the neck i have is that i lost my van keys over weekend so i have an enforced holiday! Locksmith coming tomorrow.

    S.

    in reply to: AEG Oko-Lavamat 1271 VI Turbo – not completing cycle #312673
    Simon46
    Participant

    Re: AEG Oko-Lavamat 1271 VI Turbo – not completing cycle

    Have you checked the filter? Should drain on spin within 40 seconds. make sure water is out of drum before opening. Towels down as well.

    S.

    in reply to: Teknik TKC840-2 Grill regulator #311801
    Simon46
    Participant

    Re: Teknik TKC840-2 Grill regulator

    Right.
    Managed to fit a Diamond H new version regulator single circuit simmerstat with 6mm short shaft but no pilot from hotpoint 40ER101C1P. Redrilled front panel to take screws instead of ctre nut. No pilot though which sends a live to the PCB to activate cooling fan. So temporarily wired it to load(live) so cooling fan comes on when grill element on. Not the best idea but needs correct pilot feed to PCB sorting. Any ideas on what regulator to fit? Qualtex seem to be out of stock on most.

    S.

Viewing 15 posts - 436 through 450 (of 2,216 total)