simtoms

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 83 total)
1 2 3 4 5 6
  • Author
    Posts
  • December 1, 2022 at 7:18 am in reply to: AEG W/D drier cutting out early #484639
    simtoms
    Participant

    To be honest Dave, I can’t remember how to access error codes on this model.
    Any pointers welcome.
    Many thanks
    Simon

    July 11, 2022 at 3:03 pm in reply to: AEG drum paddle replacement #482913
    simtoms
    Participant

    Thanks Dave,

    That part number is the right paddle only a set of 3.
    I managed to find the part number for an individual paddle.
    Any clues/tips on getting them to lock?!

    Always really appreciate your help and advice Dave.
    It’s always spot on!

    Simon

    May 12, 2022 at 9:32 pm in reply to: Indesit DIF04B1UK dispenser #482290
    simtoms
    Participant

    Thanks Dave.
    Officially Disgusted.
    Did someone say, Right To Repair?…

    December 6, 2021 at 9:53 pm in reply to: reed switch, rs part no. #460459
    simtoms
    Participant

    Thanks Dave. That’s great.

    December 4, 2021 at 7:29 am in reply to: reed switch, rs part no. #460457
    simtoms
    Participant

    Just hijacking this thread…
    would this reed switch be ok for Miele too?!
    Thanks Simon

    October 20, 2021 at 10:55 pm in reply to: Neff S51E50X1GB/03 error codes, no display #479503
    simtoms
    Participant

    It does seem a bit coincidental to have this trouble so soon after replacing the heat pump.
    Sounds like the thermistor plug is a sensible place to start.
    Thanks for your replies.

    October 20, 2021 at 4:41 pm in reply to: Neff S51E50X1GB/03 error codes, no display #479501
    simtoms
    Participant

    Hi Dave,

    It initially faulted because the drain pump cover had come off but this current issue has happened within a few days of fitting the pump.
    Not sure that it was immediate.
    Have you ever had a faulty heat pump that might cause this kind of issue?
    Thanks,
    SImon

    June 17, 2021 at 10:11 am in reply to: cooling fan bearing replacement #477383
    simtoms
    Participant

    Thanks Dave,

    I’ll look into that.

    Regards

    Simon

    March 5, 2021 at 11:29 am in reply to: Panasonic NA-168VG4 irratic rotating, throwing belt off. #475526
    simtoms
    Participant

    Thanks Dave,

    whenever the drum turns it’s very jumpy as though the signal to the motor is at best intermittent.
    The effect is that the drum jerks about and after a short time throws off the belt.
    It’s almost like the motor is getting conflicting signals to suddenly turn in the opposite direction.

    January 16, 2021 at 9:39 am in reply to: Zanussi ZDV12002FA stuck on wash phase #474508
    simtoms
    Participant

    Thanks Dave,
    no alarm codes when sticking on wash.
    Admittedly I haven’t gone into diagnostic mode, and I’m not sure how to on this one.
    it can’t be difficult with only two buttons and an on/off switch, but I’d be glad of a heads up!
    Thanks
    Simon.

    November 20, 2020 at 8:02 pm in reply to: Beko WDA914401W dead #473319
    simtoms
    Participant

    Thanks gents, I appreciate the pointers. Will get back and dig deeper. If I get stuck, pics will follow… 🙂

    November 20, 2020 at 7:12 am in reply to: Beko WDA914401W dead #473316
    simtoms
    Participant

    Thanks Murv and Dave

    no board fitted RHS in back although connect mention a control board but show no pic. As there’s no board there, I assume no faulty diode.
    There is a pic of the board fitted back LHS and it looks like an elaborate motor board (large capacitor and heat sink).

    August 28, 2020 at 7:42 am in reply to: Miele lid removal #471566
    simtoms
    Participant

    Thanks for replies.
    It must have the flush covers.
    I noticed a circular spot on the side of the lid but didn’t realise that it was a cover.
    Appreciate the help.
    SImon

    June 27, 2020 at 7:17 am in reply to: JLWD1612 not fully functional in drying #469996
    simtoms
    Participant

    Hi Dave,
    sorry I didn’t realize I had a response!
    Thanks for that.
    I’ve left it 10 mins and more but it doesn’t do more than turn the drum.

    September 5, 2019 at 12:46 pm in reply to: Beko WDR7543121W probs with new PCB #463087
    simtoms
    Participant

    Well you were bang on Dave, because I ordered the part number you supplied and hey presto!
    I’m not going mad after all. Perhaps.
    Thanks again.
    SImon

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 83 total)
1 2 3 4 5 6