smeghead

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 208 total)
1 2 3 … 12 13 14
  • Author
    Posts
  • September 8, 2017 at 12:52 pm in reply to: neff website #450283
    smeghead
    Participant

    Re: neff website

    ENR / S52M69X1GB/14

    Parts req’
    Sump Kit & lower door seal
    Still not wkg for me, i use the public one.

    Thanks v. much, Don

    September 6, 2017 at 10:50 am in reply to: Built in dishwasher #450226
    smeghead
    Participant

    Re: Built in dishwasher

    Hacksaw job, then block it up with wood – tell ’em what your doing first though !
    Had to do that a couple of times before where the threads rust.
    Clive

    August 22, 2017 at 6:18 pm in reply to: BOSCH dishwasher replacing sump seal SMV50E00GB/13 #449905
    smeghead
    Participant

    Re: BOSCH dishwasher replacing sump seal SMV50E00GB/13

    Hiya
    Did one of these a month or so ago, not too bad once the plastic base is off-
    unhook door springs & bend out tabs on s/s tub to release base.
    Remove heat pump , drain pump & Distributer & pipes
    I did replace the Distributer as well as i was concerned about the old O ring not fitting- & it didn’t !
    A bit daunting at first , think it took about 1.5 hrs, & no leaks afterwards, thankfully.
    Clive

    August 8, 2017 at 5:47 am in reply to: Bosch WVD24460GB/02/ stops on dry #449494
    smeghead
    Participant

    Re: Bosch WVD24460GB/02/ stops on dry

    ok Buddy, thanks for your feedback.

    August 7, 2017 at 4:41 pm in reply to: Bosch WVD24460GB/02/ stops on dry #449492
    smeghead
    Participant

    Re: Bosch WVD24460GB/02/ stops on dry

    i did wonder that Martin, but from the pic of the board online it just looks like its a relay board.
    Is there a chip on it ?
    Thanks.

    July 10, 2017 at 4:39 pm in reply to: Checkatrade #448106
    smeghead
    Participant

    Re: Checkatrade

    Been a member since 2013, works well for me
    40{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of my calls are generated by it.
    I am the only one in the area though.( the next guy is 25 miles away.)
    As far as cost- you get what you pay for !!
    Clive.

    July 10, 2017 at 4:22 pm in reply to: Hotpoint WMFUG 842P error F06 ? #448851
    smeghead
    Participant

    Re: Hotpoint WMFUG 842P error F06 ?

    Thanks M8, I did do a search here , but this post never came up.
    Cheers.

    May 4, 2017 at 9:31 am in reply to: Beko BDVC667W slot in oven – overheating #447355
    smeghead
    Participant

    Re: Beko BDVC667W slot in oven – overheating

    Thanks Dave.

    April 20, 2017 at 3:44 pm in reply to: Beko DCU 9330W. Cuts out #446957
    smeghead
    Participant

    Re: Beko DCU 9330W. Cuts out

    Thanks for the info mate.
    Always looks good if you know where to start !
    Clive

    April 19, 2017 at 5:32 pm in reply to: want spares, Try Amazon !! #446948
    smeghead
    Participant

    Re: want spares, Try Amazon !!

    & included for your £1.50 a week is all that music/ films, box sets etc, it’s a no brainer , best £79 a year I’ve ever spent

    April 19, 2017 at 4:31 pm in reply to: want spares, Try Amazon !! #446946
    smeghead
    Participant

    Re: want spares, Try Amazon !!

    okee dokey, will check UKW for spares as well then.
    Have ordered there before but from memory part took a while to come in.

    April 19, 2017 at 3:23 pm in reply to: Bosch WAS 24460 GB/08 Cuts out #446943
    smeghead
    Participant

    Re: Bosch WAS 24460 GB/08 Cuts out

    Thanks Dave,
    Don’t suppose you have a wiring diagram then ?

    March 22, 2017 at 5:57 pm in reply to: New machine dilemma ! #446041
    smeghead
    Participant

    Re: New machine dilemma !

    Cheers Martin, the bearings won’t fail !!!
    I have the power of positive thinking.
    It will also last for 10 years, ha ha.

    March 21, 2017 at 7:27 pm in reply to: New machine dilemma ! #446039
    smeghead
    Participant

    Re: New machine dilemma !

    So went for Bosch WAT28660 with idos function ; before you start I know it will block up in time, but other than that looks a decent build machine, sales guy said it is made Germany after all.
    Also comes with £50 off and a £100 fuel voucher via a prepaid card. Happy days 😀
    Clive.

    March 14, 2017 at 5:26 pm in reply to: New machine dilemma ! #446033
    smeghead
    Participant

    Re: New machine dilemma !

    Martin wrote:Save 300quid, buy a Bosch WAE28262GB. 1400rpm, split tub, brush motor, 2 yr warranty…..sorted!

    May be too late for Bosch as the other half has been to have a look & fancies the Miele.
    Well who i am I to argue ?
    Just a point , does the Miele have brush motors .?
    Thanks.

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 208 total)
1 2 3 … 12 13 14