[SparkyP]

Re: Beko WMB91442LW washing machine

Hi F07 is the first fault found.
Which then would have been reset. The 04 17 is the software version on the board. I would also go for the motor or the wires on the motor….
Hth
Sparkyp

[SparkyP]

Re: whirlpool AWOE8548 (Sixth sense)

Definitely a door lock error….I have a 9769 and it intermittently comes up f13. You can bang the front panel where the door lock is to open the door then replace door lock.
Hth
Sparkyp

[SparkyP]

Re: Whirlpool AWoD5306

Hi Bendy
Sounds like wrong part INCOMPATIBLE
481221470044 Control unit DOMINO programmed
481228210207 Control board UNPROGRAMMED

Hope this helps
Sparkyp

[SparkyP]

Re: LGF1495BDS

Hi bazza500

Any ideas how to get into these machines to access the fore mentioned items…
Cheers
Sparkyp

[SparkyP]

Re: w/pool awoe9558 f13 code

F13 is a door lock error……did customer say she could not open it at end of cycle…new door lock will cure….

Sparkyp

[SparkyP]

Re: Hotpoint FF200M Part Number

Hi Don

Thanks very much i will process ordering tomorrow….

Sparkyp

[SparkyP]

Re: Hotpoint FF200M Part Number

Hi Don

The full model no is FF200MA so i gather it will be the aluminium one….

Many thanks
Sparkyp

I have a service manual for the FF200X and thats wot they ordered for me but it was wrong size and colour when i went to the call…..

[SparkyP]

Re: BEKO WMA765S No display.

Hi Iadom

The part number you need is 2817740310. If the display is either not on or a few lit leds the main card is at fault….HTH

Sparkyp

[SparkyP]

Re: w/pool drier AWZ7913 pulse’s on to heat, then cuts out

Hi Tell

Have a look at the wires going to heater. If they are blue it needs a mod kit which is no longer available…..write it off.

The sensing part of this dryer (if empty) will only heat for around 5 secs then cut power to heater.

When u say 3 stats do you mean the ones on the heater. If so this is a single pole heater and the modified ones have a double pole heater with 4 stats on the heater……

The mod kit did include a double pole heater, control unit and wiring to convert…..

HTH
Sparkyp

[SparkyP]

Re: Whirlpool door seal

Hi

481246068532 Door bellow WH grease resistance is the correcto part number if you have any doubt……….

HTH
Sparkyp

[SparkyP]

Re: Whirlpool awz412 washer drier

Hi alsplumbing,

Have you checked the wires on the pressostat? The two double backed ones can cause a problem on spin..they are a double black and a double grey…….the single red is always ok………inspect them carefully as they are behind a sheath and very hard to see if one connection is loose……also make sure the backplate seal is not leaking causing water to drip onto motor which will cause no spin…….if you tried it, it might have dried out and spun for you……

HTH
Sparkyp

[SparkyP]

Re: Whirlpool Fault code, “CLEAN PUMP”, any ideas

Hi Troffy

Take the eco ball out……….If the customer does low temp washes the eco ball sticks and then times out after 6 mins.

HTH
Sparkyp

[SparkyP]

Re: Whirlpool AWZ7913 Condenser Drier

Auldyn

I will send a pm…….

[SparkyP]

Re: whirlpool awodas147

Hello Hello

Ntc located at the front……Take control panel off then the front square then ya cannot miss it…….probs just a wire cut loose from rast connection…..

HTH

Sparkyp

[SparkyP]

Re: Whirlpool AWZ7913 (D/W)

Hi John,

These Dryers will not work below 5 degrees centigrade,,,,,,Is it in a utility that is cold or an outhouse by any chance.

Had a load of these lately with the weather as it is,,,,,Front ntc get a hairdryer on it for a bit and try turning it on again…..It does say in the instructions about the ambient temp…….

HTH
Sparkyp

[Author]

Posts