[SparkyP]

Re: White Knight CL767C

Hi Simon,
Do you know if the capacitor was changed with the motor?
I know the motors come seperate without the start capacitor for the motor. Don’t try it yourself especially if you can get someone to do it for you. These are quite fiddly machines to dismantle.

sparkyp

[SparkyP]

Re: Whirlpool fault codes

Hi Robbra,
Have you checked the hose from the pressostat to the chambe for holes. If air is escaping thru a tiny hole you will get a fault of overfilling thus F 09

sparkyp

[SparkyP]

Re: Whirlpool MOD AVG 211

Hi Phil,
Is this an AWG211 (not an AVG211) Tumble dryer by any chance?
Sparkyp

[SparkyP]

Re: Whirlpool W80 washing machine

Hi Richard,
When you say “motor on main switch is noisy”. Do you mean the timer motor is noisy on the timer. The main switch is the one you push in to turn the appliance on. i have looked at the timer and it should say 914/1440 on it. If you do require one i have one in stock. It is very rare for the timer to go on one of these though.

Sparkyp

[SparkyP]

Re: Whirlpool won’t run

Hi John,
Does your old interlock have a wire to connect for the top and a one for the bootom. If it does do not put the new one on. The one at the top is for the machine when used on a cotton wash to open during the first 15-20 mins of a cycle so if you forget to put anything in you can actually open the door and the machine will stop. When it heats to 40 degrees the door locks and continues with the door locked. a synthetics or wool cycle it locks straight away. Anyway if you onle have one connector for the interlock it is interchangable.

Sparkyp

[SparkyP]

Re: AMERICIAN TOP LOADER

Hi Mark,
Did you smell a burning oil smell when you took the pump off etc?
It is quite common that the gearbox goes but i replace the clutch as well just in case . I preferebly open the lid and remove the conditioner dispenser and then the cap, underneath is a 11mm nut, reverse thread undo and take off the agitator. Take the shell off and lie the machine on its back. Take the pump off via the clips then the motor holders, you will see 3 13mm bolts which hold the gearbox in place the clutch comes out with the gearbox. The clutch comes as a seperate part to the gearbox and some circlips are needed from the old one. just remember the way you dismantle the old one and reverse the process.
Any questions just ask
Sparkyp

[SparkyP]

Re: Whirlpool AWZ 865 door mechanism

Hi tomQ
I have one of these in stock. Let me know if you want it and we can sort something out unless you have already gone through Dave

Regards
Sparkyp

[SparkyP]

Re: Cruelty

Hi Guys
This is class 283.5 so far
Sparkyp

[SparkyP]

Re: Whirlpool SIOS Disc Installayion Probs

Laurence,
I had problems but it has something to do with windows xp service pack 2 if indeed that it what you are running. I now just put it on my laptop which i stop all the sp2 updates and just take the critical ones

Sparkyp

[SparkyP]

Re: whirlpool awm 6111-6k troubleshooter problem

Hi almacd,
Just had the same fault on a whirlpool today. When you start the program it will lock the door then energise the pump. It is now waiting for the drum to turn to check the motor, if it does not turn the door open light will flash with the door still locked. It will either be brushes on the motor or the motor itself.

Sparkyp

[SparkyP]

Re: Hpt wms38 “door locked flashing”

Hi Seamy,
It is the board at fault if you have tried the interlock. You said you have inspected the board for dry joints and burning. Replace both the interlock and the board and this will cure.

Sparkyp

[SparkyP]

Re: Hotpoint WD52 Washer Dryer

Hi Bobhope

The connections from front to back are Grey wire on A, Black wire on B and Blue wire on C

Sparkyp

[SparkyP]

Re: LG WM-1465FHD

Hi Charlie again,
After much searching i have the code for the FE display error. It means that the water overfills due to the faulty water valve.

Hope this helps
Sparkyp

[SparkyP]

Re: LG WM-1465FHD

Hi Charlie,
It is a characteristic of this machine. When on Final spin it will open the valve and fill with water but only for a few seconds. This is normal. You have checked the filter but i would have a closer look at the impellor in the filter housing at the back. Switch off at mains then tilt the machine back then open the filter and carefully with a screwdriver try to turn the green impellor at the back. It is common to get things caught in these. As for the error code FE this is not listed in the service manual.
Hope this helps

Sparkyp

[SparkyP]

Re: Exhaust thermostat

Hi Guys
Just to confirm yes it is stock part. I think Jezzo might think i am a cowboy or something out to rip him off. I assure you i am not. But these days you have to be so careful there are people out there who give us a bad name.

Sparkyp

[Author]

Posts