Forum Replies Created
-
Posts
-
Re: Whirlpool Washer/Dryer AWZ412
The valve readings are all ok. The valve is getting a double live and i disconnected the hose pipe from the stat and still nothing. This has me baffled.
Re: Incomplete fault code list
Hi Dave, (from the service manual)
F6 Water tap close
water valve (WV1) is switched on but flow meter (FM) senses no impulses (less than 10 impulses in 10 secs) and the water indicator (WI) is at a low level
water tap closed
water inlet hose blocked
water inlet valve (WV1) defective
flow meter (FM) defective (leads to FM failure)Kind regards
SparkypRe: Whirlpool Dishwasher – ADG 722 WH, replacement heater?
Hi there,
Is this the model with the cut out on the thermostat?Sparkyp
Re: Hotpoint WMA63 bearing
Yes these are stubborn little so and so’s. Do as Martin says get a flat edged chisel and a lot of patience. You say you moved it a mm. Pesevere and it will come out. Just make sure you get a good hold on the bearing case with the chisel or a long thick screwdriver……………Good luck. Remember patience not frustration and you will conquer this.
Sparkyp
Re: hotpoint wma32 washer, drum lifters breaking
Hi Caz,
You must have the right lifters because if you had the wrong ones you would not be able to fit them, they differ where the little clips that fit into the drum.(You would not be able to line them up)Sparkyp
Re: hotpoint wma32 washer, drum lifters breaking
Hi Caz,
Just a thought to put forward to you when you replace the lifters. At the front of the drum (where the lifter will go) you will see a metal tab. This has to be lifted before putting the new lifters on. I raise the tab quite high so that when you put the new lifter on it cannot be pulled forward far enough for it to come loose. Hope this helpsSparkyp
Re: Zanussi condenser dryer ZATC7102S
Cheers guys,
I am now looking forward to having a go at this one.Cheers again guys
Sparkx
Re: Zanussi condenser dryer ZATC7102S
Hi Dave
The model is defo a TC7102S there is a link here if you want to look but it is the white model TC7102W in the link and we have the silver hence the S. Have not got the pnc number and not back in till Monday
http://www.dealtime.co.uk/xPF-Zanussi_TC7102W
Cheers
Sparkx
Re: LG WD1045S
Cheers again Dave
I will order a pcb tomorrow as soon as i get in to work. I will let you know how this one pans outSparkx
Re: Zanussi error codes?
Cheers Dave
I will have to find out tomorrow as it is for a friend in the trade who i work with. I think he wanted the codes espeically the instructions to reconfigure the board if need be. I will find out what code it is flashing up and let you know.Thanks again
Sparkx
Re: Ariston Margherita 2000 – I also have a problem!
I had a call like this just the other day. It turned out to be the waste pipe was stuffed all the way to the bottom of the outlet pipe causing siphoning. Then the machine just stopped. I raised the waste pipe to the normal level and the customer has informed me that it was working ok now (they had just moved house). Have a look at your waste pipe and see if it is pushed all the way down, if it is raise it up. If you have a connection that goes into your sink trap disregard the above notice. Hope this helps
Re: Creda washing machine burning out motors
There have been problems with the replacement brushes on hotpoint and creda machines and there solution is to fit a new motor which requires you to cut of the white motor plug loom and rewire with a yellow plug in the kit. Hence re con motors have the brushes in that fail often. You can tell what type of brush is in the motor. If it is a nylon type brush it is the unreliable one. The old type were a pot type which could withstand the heat from the motor. Hope this helps
Re: hotpoint wma32 washer fault
If it is not the door lock it will be a combination of a new door lock and control module……be warned if it is the door lock do not try a new control board with the old door lock……..
