Forum Replies Created
-
Posts
-
Re: Hotpoint FF92 Frost Free “P1” Error
Have given it chance but still nothing in inbox!
P1 is not an error then?
™
Re: Hotpoint FF92 Frost Free “P1” Error
iadom wrote:I have deleted your post in the 5 year old public forum thread.
Check your inbox. 😉
Inbox Empty!
😥
Re: Tecnik repairer for Blackburn
Hello there,
I can do it but not until next week!
TM
(Send me a PM for contact details)
Re: Hotpoint fridge freezer Model FF92
Hotpoint FF92
I have an error code shwoing of “P1”
Having tested the thermistors/sensors, the green one is open circuit.
Is this the Fault code?
™
Re: Refrigeration ‘interim personnel certificate’
Well, ! I still never received my certificate!
Where do we go now?
TM
Re: Worst Week Ever
leavemetogetonwithit wrote:Ok, can anyone
Without wishing to wander too much further off topic, something.
Mike.I agree!
Re: Worst Week Ever
Well, we are quieter than ever.
One major work supplier has reduced our are down to just one post code, suggesting we are too expensive.
Nothing wrong with our quality or level of service, that we already know.
However, when they ask us to go back and mop up after our replacements, its pretty clear why they are so cheap. They can’t do the job with inexperienced kids or arrogant old blokes on £5 an hour.
Re: meggers
Martin wrote:
adv wrote:
i dont need a megger if a washer aint spinning. brushes belt module. not draining. mmm hink thatl be pump or a blockage. oven naw heat element. over heat state? fridge naw go compreeser. or state. got a pac 1000 pat tester tho 😆 any way. when put on test ie hold button down for 60secs.p1 an p4 flash twice. at end same as orignal board doesErrrrr?….can you put it another way please my enigma machine (ooops sorry – megger) isn’t getting a reading on that right now. 🙂
Would you like to take up my earlier offer though I wonder?
lee8 wrote:Isn`t it now part of the law that all appliances are safety checked including insulation test, Earth loop impedance and earth continuity.
Sadly I have to report that no such legislation applies, the law doesn’t carry a megger on the van either. :rolls:
Well Maybe it should be Law!
Re: Refrigeration ‘interim personnel certificate’
THANKS
That is assuming the Post Office have not lost em~!
Re: Refrigeration ‘interim personnel certificate’
Dales-Electronic wrote:The interim certificate is to do with experience not the type of tools that you use. If you were able to submit some form of evidence that you have worked on CFC/HCFC gased appliances you could have registered for the certificate. Unfortunately, the closing date was 4th July 2009. 😥
I sent my application of to the UKwhitegoods site and had no response as yet!
Re: refrigeration repairs.
roly16 wrote:a) If the motor’s running but it’s not getting cold scrap it.
b) If the motor’s not running but it’s hot and the fridge isn’t getting cold scrap it.
c) If the motor’s not running and it’s cold check the thermostat.
Not the thermostat? Phone your friend.
A Pressurise with OFN to leak test, find leak and if possible repair leak, evacuate system and regas.
B Very often a thermostat. On older apppliances where a heater is fitted behind the evap, when the thermostat goes o/c (corrosion leads to gas in thermostat capillary leaking out) heater is energised full time, leading to heat.
Could also be PTC/Relay or compressor.
C does not make any sense!
Do you mean if the compressor is cold?
Re: meggers
I thought we all carried a Megger?
I do not understand how an Engineer can work without one?!
