Forum Replies Created
-
Posts
-
Re: BEKO cda563fw
hi is the compressor hot to touch? is there a even heat across the evaparator when the compressor is running? is there a build up of ice inside the freezer ??
Re: Which 1600rpm 8kg washer? Siemens, Panasonic or… ?
hi i think i would buy a hotpoint aquaries comes with the same warrenty but its alot quietier
Re: Whirlpool ARC 4030 problem
hi iv come across this problem a few times sometimes it can be the control panel aswell as the control board this would be alot cheaper to replace
Re: ikea whirlpool dwh b10 4 flashes
hi it sounds to me you could have a faulty presso stat, quite a common problem on whirlpool dishwashers
Re: Whirlpool Type ART706 Model 3xART720 Fault
hi have you tried a new mains lead as sometimes you get a short on them
Re: “FA” Error Code on a Whirlpool ADP6940
hi, i would check to make sure water is gettin to the valve, also make sure the waste hose is not to low into the drain, check this first then get back to me
Re: whirlpool dishwasher adp4601
hi you know you said you fitted a new drain switch do you mean a switch diaphram, was it round in shape
Re: Whirlpool ADP 4501 loud buzzing then shuts down but no c
does it only make this noise when the spray arms are going round, if so it can only be the circ pump its the only moving part on the dishwasher apart from the drain pump, like you say those pumps aint cheap, if you want the part number for the circ pump send me the 12NC number or service number as its sometimes known and ill get you the part number
Re: Whirlpool ADP 4501 loud buzzing then shuts down but no c
hi its sounds to me that your circ pump has gone, can you hear the spray arms going round
Re: Whirlpool Dishwasher ADP556
hi john the non return valve is to stop water flowing back into the dishwasher if its connected to the sink, if the waste pipe of your dishwasher is connected to the sink just raise the waste pipe as high up the kitchen unit as possible and this should stop any dirty water going back into the dishwasher, hope this helps
Re: Whirlpool ADP 2440WH
did you notice if the start button was flashing at all when the dishwasher first went off, i would be very suprised if there was a problem with the timer, they do go but very rarely, ill see if i can get the test programe for you
Re: Whirlpool ADP 2440WH
hi the part number for the switch diaphram or pressostat is 481227128407, its an easy job to change it, remove the plinth at the bottom then there is normally 4 screws holding a metal plate onto the cabinet remove that, then 2 screws holding the bottom plate to the cabinet remove that to, then locate the switch diaphram, by looking at the new one you will be able to see how to remove it, just remember when fitting the new one you might have to reuse the old seal its a thin black band to keep it water tight, hope this helps 🙂
Re: Whirlpool AWM 336
hi iv worked on whirlpool for 16 years and it aint worth fixin not worth the time and money
Re: Belt Drive Replacement Whirlpool AW 7814 AL Dryer
hi its realy easy to do just remove the back and hang it over the left hand side, remove the conveyour and hang that over the left hand side , no need to take any wires off, remove the rear fan cover, remove fan and inner cover pop the belt on and reasemble
Re: Whirlpool ADP 2440WH
hi it sounds to me like you have got a faulty pressostat, the dish washer thinks it full of water and therefor keeps wanting to empty, very common problem on the whirlpool, if you send me the service number ill look into it tomorrow for you, you will find the number down the right hand side of the door if facing it from the front, it usaly begins in 85
