Forum Replies Created
-
Posts
-
Re: Common sense – spam
maltheviking wrote:
whitevanman wrote:
Who said that then ❓ The pope ❓ 😆I like it ‘tutto è giusto nell’amore, nella vita, nella lavatrice, nella politica e nella religione anche se rilasciate le dichiarazione circa i musilims’ 8)
Thats easy for you to say 😉
Gratzi
Re: Common sense – spam
maltheviking wrote:Who said that then ❓ The pope ❓ 😆
I like it ‘tutto è giusto nell’amore, nella vita, nella lavatrice, nella politica e nella religione anche se rilasciate le dichiarazione circa i musilims’ 8)
Re: Ariston LSV66 Door Won’t Open
To be honest without being able to pull the dw out of situ you have got a big problem, however I would suggest you contact a local repair person try http://www.ukwhitegoods.co.uk/modules.p … whitegoods
They may or may no be able to open door without causing some damage to the facia/panel on your dw. this would be cheaper that replacing the machine,
Hope this Help
Wvm
Re: Electra AWm 900b Wont empty properly
sound like the pump to me
what the full serial no of this washer as it may be manufactured by Hotpoint or probably Servis
WvmRe: Problem with Zanussi RS-3T
Ciao enry, i bracci dello spruzzo sembrano essere ostruiti, recomend che utilizzate un disincrostatore del calcio dal supermercato locale e questo aiuterà pulito la vostra lavapiatti, che zona voi?regards in tensione
speri che questo aiutiWayne
Re: Problem with Zanussi RS-3T
Seller wrote:Hello to all, excuse for my English, I am Italian.
I have a problem with one Zanussi RS-3T.
In phase of washing the shovel up does not turn, while that inferior is OK. It can depend on the pump that does not send water up to the tube?
The pump, is always the same one also for that inferior?Best Regards
EnryCiao a tutti, giustificazione per il mio inglese, sono italiano. Ho un problema con uno Zanussi RS-3T. Nella fase di lavaggio della pala in su non gira, mentre quel inferior è GIUSTO. Può dipendere dalla pompa che non trasmette l’acqua fino al tubo? La pompa, è sempre stesso quello inoltre per quello inferiore?
Che cosa voi significano dalla pala in su
La rondella non vuota???riguardi
wayneRe: annoying leak on zanussi 1200
whitevanman wrote:
Transit-van-man wrote:
Hi,
yet every morning its sat in a puddle 🙁is the machine left running over night ???
common sense !!!!
its not outside is it and its rained overnight ?
Is the mains water tap behind it/ is is dripping only at night though?
IS the machine water valve letting in water due to low water pressure?
Is the filter screwed in properly?
Is the floor level and are you sure the water puddle is not comming from somewhere else ?
Has the hose from tub to filter housing got a small hole in it, like its been pricked by a bra wire or something ??
Has the drain hose got a small hole in it ??
or as eastlemark says is the rear circ pump leaking ??? or as P45 says is the water leaking down the inside of the machine??
101 Suggestions U C, Sometime the dog has got 2 c the rabbit
JOE OR PRO YOU SEE ??
Re: annoying leak on zanussi 1200
eastlmark wrote:white van man helping transit van man, i like it 😆
😳 :rotfl:
Re: annoying leak on zanussi 1200
Transit-van-man wrote:Hi,
yet every morning its sat in a puddle 🙁is the machine left running over night ???
Re: Hoover Performa 1100 ( AC110 )
bevw wrote:He’s O K with car engines, havn’t let him loose
on washing machine before.thanks again . cheers Bev.
Similar to the brushes on an alternator on the car, let him have a go , if not as p45 says look up a local wg engineer
Re: Bespoke kitchen ding dong!
effzedarr wrote:a service bulletin went out the next day advising all engineers NOT to remove any built in appliances ,
that would be the disclaimer which legaly was not worth the paper it was written on 😆 moat
Re: Candy AQ141T
DentedPorsche wrote:I’m gobsmacked 😮
Anyone got any info on these machines?
All assistance gratefully accepted.Thanks
Briancheck ur email brian
Re: British Gas Homecare
gegsy wrote:
DentedPorsche wrote:
I’m definitely not one of the “can’t be bothered” brigade. I’m not afraid of hard work, and bearing and tub changes aren’t hard work at all.
So please, don’t brand all BG engineers as being the same, we’re not. I take pride in my work and I don’t chase bonus.I wish there were more BG guys like you.
The clown up here who I have to sort out after is doing BG no favours.
19 times to washing machine he made as it was leaking and sticking 8O, I got there after guy gave up, just to find that hot tap was damaged (poor flow)and weeping.
Im not the hottest engineer by far but this is basic stuff :rolls:Greg
That must be Bibby , ehh brian lol , bonus chaser/acts etc etc
Re: Child Safety READ THIS
kwatt wrote:Another one Mal (which happens to be a pet of mine) is the BEAB regulations on external temperatures for cookers. Far, far more dangerous and far, far more common to cause burnt little fingers due to the manufacturer cost cutting and yet not BEAB nor anyone else seems in the least interested in doing anything about it. K.
Buy a baumatic (in house & home mags etc) top quality machines 😛 approved with the CE mark not BEAB, single oven without cooling fan facia will get to 96C Baumatic said this was satisfactory.
The other point how many manufactures use BEAB in the UK, Brother ditched this due to them taking 6-9 months for a product to come back with their approval. and moved towards BS.
