Forum Replies Created
-
Posts
-
Re: white knight wk767 no drum drive !!!!!! help me im melt
Just a thought Have you checked the door striker / microswitch is all okay, also is mcsw in water collector okay ???
Wvm
Re: hotpoint grill element
try this link
http://www.elementman.com/proddetail.as … 398&cat=28Re: OKO -LAVAMAT 72640 continially goes on to pause
I have similar fault on my AEG 76669 very occasionaly, wm is found paused anywhere in cycle, presing start continues the cycle, collegues in the same trade advise me is the control board however I would advise you to try Repairs@ on left, as would require technical expertise to configure board.
hope this helps
Wvm
Re: Refrigeration Tips?
Dales-Electronic wrote:I guess you have never been at the wrong end of an isobutane blowlamp!!
Point taken with the Blowlamp, Obviously common sense would apply where a system would be low on gas and care would need to be taken but if there was a big leak most of the gas would have been dispersed into the atmosphere and not forgeting that the correct mixture of gas and air would be needed to cause an explosion.
The suggestion to use a lighter as I have used has never caused me any problems but before I test an area with heat I would test with a soapy solution to check for any bubbles and this has never failed me.
Wayne
Re: Refrigeration Tips?
lokring wrote:JEEPERS!! 😡 i hope you dont try it on an R600 system this is NOT best advice…….
I would not have thought this would have been an issue with the small ammount of gas that the system would have contained, 100grms etc
other alternative is to put a cannary in the fridge or freezer compartment :rotfl:Re: Refrigeration Tips?
This one may work to find out is there is lack of gas , place lighter on pipework as it comes out of the compressor in theory I will absorbe the heat if its still hot it suggests there is lack of gas.
Obviously partial freezing or an iceballing on a wetwall/skin evapourator is another indicator.
Re: is there a slim washing machine
bzz67 wrote:I called on an old servis quartz this week, that after 20 years service the motor bearings have siezed up and the drum bearings have gone
If you cannot source a machine I have a bearing kit both for the polytub & vitreous tub also motor going for a song PM me if you are interested
Customer satisfaction and all that !!!
Wvm
Re: Diplomat ADP1180 Gas Hob – melting knobs
thelittlechef wrote:Hi,
(as the hob is less than a month old)T
Look at the Sale of goods act (28 day) is the product of merchantable quality ??
I would ask for my money back but I dont now if this would include instalation cost only you can decide.thelittlechef wrote:
if not – where can I get a new knob myself – and is it a user fittable part?
TAny part which is removable without any tools can be replaced by anyone
Hope this helpsWayne
Re: LG Washing Machine dispenser leaks
Penguin45 wrote:IIRC, there were a spate of these a year or so back – you have to replace the dispenser box.
Chris.
You would have thought they would have taken some notice of the similar fault on the hoover soft & new wave range of machines.
will a restrictor in the inlet valve help ? , just an idea got 2 b cheaper than replacing dispenser
wayne
Re: Zanussi ZT605 d/washer not drying!
effzedarr wrote:Hi this is something i’ve never come across before, customer says the pots etc are warm/hot after the drying cycle but the’re damp ,especially the cutlery. I first fitted a drain pump as this was noisey , so I suspected after a long wash prog the pump was playing up, now nice & quiet but still damp pots! The prod # is 911825033.
Why is it always d/washers that give me grief 👿 ?
cheers Chris… 8)Lack of rinse aid dispensed can sometime cause this problem, just a thought it may be the cause ???
wayne
Re: White Knight 797c
hi 99{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} sure its the brush sensor which is fiited inside the machine
:zap: disconnect the power before investigating :zap:
Wayne
