winker

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 75 total)
1 2 3 4 5
  • Author
    Posts
  • October 20, 2022 at 6:44 am in reply to: Neff combined microwave oven. C57M70N0gb/01……Heating Fault #484117
    winker
    Participant

    That would be great Dave if you can,appreciate it

    steve

    July 28, 2015 at 6:24 pm in reply to: Bosch washer dryer WVD245S3gb/06 #429098
    winker
    Participant

    Re: Bosch washer dryer WVD245S3gb/06

    Just to update
    Machine on 60 cottons washes til display gets to 39,aborts,empties and releases door.
    Water heats and cold wash only washes cold.
    Insulation test shows clear.
    Could the ntc cause this,whats the typical value at room temp and say 60 degrees.

    July 23, 2015 at 8:27 pm in reply to: Bosch washer dryer WVD245S3gb/06 #429096
    winker
    Participant

    Re: Bosch washer dryer WVD245S3gb/06

    This is happening on all wash cycles

    March 7, 2015 at 6:36 pm in reply to: Siemens washer wm14q360 gb/15 #425314
    winker
    Participant

    Re: Siemens washer wm14q360 gb/15

    Thanks for the help.had checked child lock.sadly it is the pcb

    March 4, 2015 at 9:14 pm in reply to: Siemens washer wm14q360 gb/15 #425312
    winker
    Participant

    Re: Siemens washer wm14q360 gb/15

    Thanks Martin,those components are so small on the PCB,bring back valves !

    November 22, 2014 at 5:41 pm in reply to: Bosch coding info #421758
    winker
    Participant

    Re: Bosch coding info

    Thanks to all senders of replies.will let you know outcome

    November 20, 2014 at 5:52 pm in reply to: Bosch coding info #421755
    winker
    Participant

    Re: Bosch coding info

    Martin,are you saying corrupted rather than blown and therefore recoverable by recoding.I found the dispenser would open on a prerinse and as previously stated
    machine does heat.Are there coding instructions available

    November 20, 2014 at 1:38 pm in reply to: Bosch coding info #421753
    winker
    Participant

    Re: Bosch coding info

    No i havent changed the control unit.But it was changed 4 months ago by a Bosch
    approved agent due to recall.The cycle time for quick wash 35 comes up at 142 mins instead of 30 mins and the other cycles are wrong.The heat is working as i found yesterday on test.The reported fault to attend was soap dispenser failing to open.

    March 18, 2014 at 7:10 pm in reply to: Siemens dishwasher SN26M830gb/01 #411014
    winker
    Participant

    Re: Siemens dishwasher SN26M830gb/01

    well returned to the dishwasher,after five cycle starts lasting seven minutes a piece,i can confirm the following and hope this may prompt some replies.The machine cycles both the wash and drain pumps and proceeds to fill and circulation.On the sixth cycle start it runs the drain and wssh pumps but never started to fill…the solenoid on the valve never energised.E24 comes up and the check water tap symbol.Does anyone know whether the wash pump feeds back a signal to the microprocessor in the same way as the drain pump does.All advice welcome.

    August 24, 2013 at 10:57 am in reply to: Zanuss washer dryer ZWD 14270w #399950
    winker
    Participant

    Re: Zanuss washer dryer ZWD 14270w

    thanks for the reply,i was thinking that way,the pump still works tho ? can that that be ?

    June 25, 2013 at 7:51 am in reply to: Hotpoint help needed #396835
    winker
    Participant

    Re: Hotpoint help needed

    Hi Bob its aqdpra69pmtuk if that helps,programme 00237

    steve

    June 16, 2013 at 4:19 pm in reply to: help needed #396427
    winker
    Participant

    Re: help needed

    No job offer I am afraid but looking for a mates rate reprogramme on an aqualtis module.If thats out of order…sorry
    but back in the seventies when i was at hoover beer and petrol was important !!!

    June 14, 2013 at 11:30 am in reply to: Hotpoint Aqualtis AQ113D697E #396035
    winker
    Participant

    Re: Hotpoint Aqualtis AQ113D697E

    looking for indesit or hotpoint engineer close to gu478qu who can help pm please

    June 7, 2013 at 11:59 am in reply to: Hotpoint Aqualtis AQ113D697E #396029
    winker
    Participant

    Re: Hotpoint Aqualtis AQ113D697E

    tried that there not even on them yet

    May 29, 2013 at 3:34 pm in reply to: Zanussi diagnostics ZWF1437w #395682
    winker
    Participant

    Re: Zanussi diagnostics ZWF1437w

    richardandrews76@aol.com

    thanks dave

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 75 total)
1 2 3 4 5