Forum Replies Created
-
Posts
-
Re: adp5540 whirlpool d/w
Galway wrote:do you know which reed switch it is as this job is not near me
thanksive read on here its CL37 but not tried it personally, hth.
Re: adp5540 whirlpool d/w
Galway wrote:thanks but can the flow meter be ordered on its own?
not as such, you could buy the reed swith from maplins and solder it in yourself, ive got some on order should be delivered soon so watch this space 😉
Re: Business plan???
ive done the rbs plan its actually quite good, im not looking for it for financing or anything, all my start up costs are self funded 😥
i was talking to business gateway about taxes etc and they suggested i do a plan and bring it in and they would help, other than that i dont see a need for a plan either..
thanks for the advice guys
Re: ADP8322 motor
yeah you can get a tool, but you can get away with using a small screwdriver to open them and a pair of snips to close again.
Re: ADP8322 motor
if you are carefull with the old clips you can reuse them,
straight forward job tbh, youll need 2 screws to attach new motor to back panel, it slots in and pushes up till screws line up, attach hoses and test.
20 minutes tops..
Re: Hotpoint Indesit Tumble Dryers Scrape after fitting drum
is there not a mod out for these that you fit an extra washer between the support and the backplate, which pushed the drum further from the back panel???
im sure in the v4 shaft kits a new washer is there and thats what its for.
Re: beko door seal
front comes off, open filter door, 2 screws and plinth moves right then out.
3 screws at bottom of front panel hold it on, undo door lock and seal and push panel down it is clipped on and both sides.you need to remove concrete block 5 torq bolts hold it on it is a pig to get off even with bolts removed might be best to remove facia panel 1st but you cna squeeze it past.
once weight is removed remove the hose at top and spring clamp round seal, refit new seal and rebuild in reverse,
good luck you’ll need it 😉
Re: Just starting out on my own…Help needed !
hotpnt wrote:Just for any of you looking to stock up on parts, I have a shed full of parts, for Hotpoint, Indesit, Creda, Ariston, all parts need to be cleared, theres a lot there if anyone is interested??
hi mate would be interested if price was right, email me a list of what you have including prices, i will probs bulk buy so make it a good deal 😉 .
Re: ebay sales
bazil wrote:I have a large quantity of Whirlpool Spares new and boxed all in common use and for appliances mostly less than four years old. I cannot find a buyer for these so if you were me what would you do. Put them on fleabay for half trade?
id donate them to an up-coming new buisness trying hard to keep costs down 😉
Re: Just starting out on my own…Help needed !
A1TEC wrote:
A1engineer wrote:
just quicky!!i am currently corig registered for the company i work for, as i am starting out myself i was wondering what i need to do to change the registration over to my new company??
can anyone tell me how easy it is and what costs are involved.
cheers guys
Kev.
Hi Kev, you need to register with the Gas Safe Register, who take over from Corgi at the end of March.
It will cost you more first time because of the regisration fee and after that i think it’s around £175.00 per year
Do you have the dom gas safety and ckr1 tickets.?
Thats about all you need to get yourself registered.
John.
Hi John, Yes i have CCN1 and CKR1, is this all i need??
cheers
Kev.Re: Just starting out on my own…Help needed !
just quicky!!
i am currently corig registered for the company i work for, as i am starting out myself i was wondering what i need to do to change the registration over to my new company??
can anyone tell me how easy it is and what costs are involved.
cheers guys
Kev.
