A1engineer

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 402 total)
  • Author
    Posts
  • in reply to: CURRYS KNOW HOW #349030
    A1engineer
    Participant
    in reply to: Indesit WIL163 drum removal #373789
    A1engineer
    Participant

    Indesit WIL163 drum removal

    I’m afraid that seems like your best option now.

    in reply to: Rangemaster proffesional 110 #373785
    A1engineer
    Participant

    Rangemaster proffesional 110

    Yeah there is a grill if you turn knob right round to end clockwise there is a click and that’s you on grill

    in reply to: Indesit WIL163 drum removal #373787
    A1engineer
    Participant

    Indesit WIL163 drum removal

    Sounds like you have a metal( tin) tank if so outer and inner drums come as a complete unit.

    in reply to: CURRYS KNOW HOW #349026
    A1engineer
    Participant

    Re: CURRYS KNOW HOW

    shifts are 5 on 3 off, doenst seem like they have had much success attracting engineers by sounds of things.

    in reply to: CURRYS KNOW HOW #349024
    A1engineer
    Participant

    Re: CURRYS KNOW HOW

    Has anyone heard any more about this, 1 of the local engineers i know has been offered a job with them but knows nothing about it???

    in reply to: hearts v hibs cup final #373572
    A1engineer
    Participant

    hearts v hibs cup final

    Tickets arnt out yet, dont imagine itll be a problem, around 20k each so should be more than enough for both sets of fans

    If you get stuck let me know tho, should br able to get a few.

    in reply to: Indesit washing machine #373328
    A1engineer
    Participant

    Re: Indesit washing machine

    ddirect wrote:Went through the reset procedure today and still no difference??
    Going to hit it with a big hammer any more thoughts ??????


    your gonna need a bigger hammer!!!!

    the reset can be a bit of a hit and miss, i had one last week tried everything to go didnt work ordered a pcb and smart card, however when i returned the machine miraculously was working!!!!

    in reply to: DSG/RepairCare Rate Cuts #322770
    A1engineer
    Participant

    Re: DSG/RepairCare Rate Cuts

    Has anyone heard any more about this, 1 of the local engineers i know has been offered a job with them but knows nothing about it???

    in reply to: Whirlpool ADG 7560 Error code 6 #373187
    A1engineer
    Participant

    Whirlpool ADG 7560 Error code 6

    If it fills then its probably flow meter if it doesn’t fill but valve buzzes it’ll be valve, of you don’t here it buzzing check for broken wires in door.

    in reply to: Whirlpool adp5406 #372683
    A1engineer
    Participant

    Whirlpool adp5406

    Pm sent

    Thanks for your help

    Kevin

    in reply to: oven constantly heating #370473
    A1engineer
    Participant

    Re: oven constantly heating

    have a few with element constantly on even when switched off, traced fault to selector switch with welded contacts, the old hotpoints were bad for it, seen a few range cookers, bekos and diplomats with similar fault recently.

    in reply to: hotpoint aqualtis AQ9F49 UK V #369971
    A1engineer
    Participant

    Re: hotpoint aqualtis AQ9F49 UK V

    last one i had ended up getting new board to sort it, apparantly theres a firmware update on the boards :nono:

    in reply to: Kenwood Dishwasher #369959
    A1engineer
    Participant

    Kenwood Dishwasher

    Most likely just the screw in type cutout stat at rear of machine above motor, if not could be Heater/wiring/module, obv you got to hope its the simple one lol

    in reply to: Diplomat dishwasher – ACA9102 – Not programming #369476
    A1engineer
    Participant

    Diplomat dishwasher – ACA9102 – Not programming

    Have resent to that email address.

    Kevin

Viewing 15 posts - 106 through 120 (of 402 total)