[A1engineer]

Re: Indesit IWD7145S module

i agree with hotdog, the dryer thermsitors cause weird faults too.

if its working again id suspect bad connections tho.

[A1engineer]

Re: Diplomat dishwasher – ACA9102 – Not programming

motor part number – 012G9380538

i have emailed you the service manual to the email address linked to your website.

HTH
Kevin

[A1engineer]

Re: Diplomat dishwasher – ACA9102 – Not programming

will probs still be a motor fault, ive done loads of these with those symptoms.

[A1engineer]

Re: Diplomat dishwasher – ACA9102 – Not programming

insulation fault on wash motor.

might have water in base you might be able to fix leak(if there is one) and dry out motor, but chances are itll need replaced.

[A1engineer]

Hotpoint AQXGF149PIUK F01 Fault

I’m afraid it’s one of these faults it could be motor or module mibee even the wiring, you can check the motors for resistance of the 3 fields and tacho

A betting man would say module fault tho

Kev

[A1engineer]

Re: aqxxl129pi Aqualtis

f11 no supply to drain pump, check pump wiring and module.

[A1engineer]

Re: diplomat 8242 smeg type dishwasher

cant find your email so ill stick answer here.

With the door open, turn on the appliance and within three seconds push 4 times on the program selection
button – The test program has been selected if the SOAK and STRONG LED’s (1&5) are flashing
This LED combination represents the test program for the appliances that have a flow meter.
If the above indication is not shown on the appliance, switch the appliance off and try the sequence again
until the above LED’s are shown on display.
Now push on the program button once more to select the version ‘without flow meter’, check that the SOAK
LED goes out, and the display is indicating on-off-off-off-off.
Do not close the appliance door, to complete settings switch the appliance off.
Now switch the appliance ‘on’ and test on a SOAK program.

[A1engineer]

Re: diplomat 8242 smeg type dishwasher

probably just needs reset pm me your email ill send you some info

[A1engineer]

Re: Hoover HNWF3137 – 31000638

ok will have a look tommorow,

no there is no fault code, just fills then sits there, or on spin drains and sits there.

cheers
Kev

[A1engineer]

Re: Hoover HNWF3137 – 31000638

thanks for that bob, could the dryer module cause no motor action, i saw it but didnt take it out to have a look.

i did wonder about relay, looked ok might stick a blob of solder on it just incase.

thanks for advice.

Kev.

[A1engineer]

Hygena AHY8102/1 Lower sprayarm

bump from 6 years ago but found this post with the search on ukw, managed to work out why the machine I was at was leaking from the door.

Cheers Andy.

[A1engineer]

Re: Diplomat ADM 8513

module fault, have a look for dry joints on board, i usually just replace module tho.

[A1engineer]

whirlpool adg7560/1 6 flashes

Flow meter on left hand side otherwise known as airbreak, try cleaning and pinching the contact at reed switch.

[A1engineer]

Hotpoint CTD85A problem

Belt is on wrong, the pulley should go at back of belt, not enough tension to turn load the way u have it.

Good tip to fit pulley, loosen far away screw 1/2 way, fully remove one nearerst you.
Push pulley right back until it is past belt, fit belt around pulley and pull towards you until the clip on pulley locates at motor,
Refit screw and tighten both.

[A1engineer]

Re: bosch waa24171gb

could well be door lock, just check it doesnt just need the fault code reset tho, turn the dial to off, then to 6 oclock. hold in spin button and turn 1 click to 7 oclock, let go of spin button. turn back to off then on again and give it a go.

HTH

Kev

[Author]

Posts