Forum Replies Created
-
Posts
-
Re: Buying Advice
don wrote:Hi
But if you start with the upper end of your budget then the Bosch SMV50C00GB if it’s a fully integrated machine would be a good start point.Just to tag on to the thread what would be a sensible next step up in quality / price from this model? Thinking of longevity.
Currently got an integrated 9 year old Neff with the trays corroding badly now and the detergent dispenser falling apart. Spare parts last time I looked would have been getting on for £300 😯
Re: Rosieres 4040DB
Hi
It’s not just a simple lift the hob top off. The whole appliance needs to come out and both the solid cast iron plate needs to come off first. And then the rest needs to come apart. Easy if you’ve done it before but nightmare if you haven’t.
Bryan
Re: Neff dishwasher S4943N1/08 info
Thanks for the answer and tips… but in order to be sure where I have to dig it up I will need to know what kind of error is in >>>
This NEFF SK549A must be similar with one Siemens or Bosch so it should be there such info…
Re: zanussi zwg1120m
sandysuds wrote:e62 have checked tacho and no sign of blow at the pbc
Do i need a new pbc
Thanks
Sandy.E62=The speed feed back signal abnormality 😈
The only thing you have to do is just to change motor triac….
AND DO NOT PUT CHINESE SEMICONDUCTORS… and will revive… 8)And give another check to tacho magnet(for any damage/crack) / coil for interruption when is heated…
Re: Hotpoint Aqualtis AQGD 169
F18 means faulty communication between microprocessor and DSP (Digital Signal Processor).
I didn’t met such error so I could not help you further…
The only doubt I have it’s about “eep” file version because sometime the eeprom does not match always with commercial code (depends also by PCB code) … that’s a little bit hard to do if you do not have such equipment (hardware & software )…Re: Howdens HJA0150 600 Gas Oven
Hi
The most probable cause is a FSD failure stopping the flame from reaching full heat.
Bryan
Re: SAMSUNG SR-S2028CSS TRIPPING CIRCUIT BREAKER AND LEAKS
Hi
E-mail me samsung@ffrservices.co.uk we can supply a kit to repair your fault.
Bryan
Re: neff K3990X6gb04 "american style" leak from fountain hos
HI Mark
Yep the insulation would have failed and it’ll be a complete door. Walk away as if the cladding does need to come off then the likelihood that it wont come off cleanly is high and you’ll get blame for it. Not worth the hassle plus the door will be in excess of £500.
Bryan
Re: Miele Fridge Freezer KFN 8452SD Alarm
Hi
Your appliance is made in the Liebherr factory so either a miele or liebherr engineer should be able to fix it. Where about are you as a guess you are within our service area and we are liebherr engineers.More likely to be a sensor fault rather than a system fault.
Re: iPad/iPhone Protection
Was gonna get the boys a iMac last week..glad I didn’t.
I know its gonna hurt but not as much as if I bought a microsoft machine.
Bryan
Re: whirlpool spanner
Hi
If its the same kit that fits the maytag toploaders then I have one sitting on the shelf
Bryan
Re: golocal reactive
GO LOCAL REACTIVE LIMITED
The following changes have been detected:
23 Oct 2012
New Company Document Available
Form: GAZ2(A) –
FINAL GAZETTE: DISSOLVED VIA VOLUNTARY STRIKE-OFF
Purchase a copy of this document for £4.99 + VATBryan
Re: Zanussi E20 error code, but it can drain…
Ok, had a go but nothing happened, for some reason decided to hold down the start/pause and the skip/reset button and then it did all light up, the led’s lighting up in sequence.
I started to push some of the buttons and all that happened was the machine started filling with water, the only code that came up was EEO, don’t know if that means anything to you or anybody.
I probably didn’t do the test correctly, but it was worth a shot…
