Forum Replies Created
-
Posts
-
Re: Kenwood dishwasher under-heating E3
Hi
there is a modified pressure switch for this haier model which allows the extra fill level.
I will get the part number later todayBryan
Re: Emergency Services Ltd.
this one ??
Name & Registered Office:
EMERGENCY SERVICES (UK) LIMITED
LESLIE HOUSE, 6 ALLEN ROAD
LIVINGSTON
WEST LOTHIAN
EH54 6TQ
Company No. SC275026Status: Dissolved 21/08/2009
Date of Incorporation: 21/10/2004Country of Origin: United Kingdom
Company Type: Private Limited Company
Nature of Business (SIC(03)):
7486 – Call centre activitiesAccounting Reference Date: 31/10
Last Accounts Made Up To: 31/10/2007 (DORMANT)
Next Accounts Due:
Last Return Made Up To: 21/10/2007
Next Return Due:Last Members List: 21/10/2007
Previous Names:
Date of change Previous Name
10/03/2005 24SEVEN (GB) LIMITEDRe: X Factor 2010
i kept having to get up off the sofa as some ….most of them were so embarising
😳 😳 😳 😳 😳
Seamy I have user manual… It isn’t usefull at all… isn’t say there nothing about how to get out from DEMO, neither other details for servicing…
For ex. only in service mode you can change preset language; how it is connected to water supply (cold or hot) etc…P.S. The info can be in any language: Deutch, English, Francoise or Italiano :help:
Re: Miele professional PW6065 problems
Nobody who has data from Miele here? 😯
PS. Machine number:06183160
In user manual it does not say anything for getting off from DEMO… 👿Re: SIMPLE PCB REPAIR TIPS
LJDomestics wrote:just done a repair to exact same board as chris has posted here, FAULT = NO HEAT ( d3 ) locate and change the little resistor that says IN4007 24C
1N4007 it’s a diode not resistor…
neilsukwg wrote:Does this meter allow you to test a capacitor while still in circuit?
NeilIt’s cheaper to unsolder at least one leg of capacitor for measurement instead of buying expensive tool… before measurement make sure to discharge capacitor and do not replace him if is inside tolerance of 10{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} of his value (isn’t necessary)… This is applying to unpolarized capacitor like those from above photos and not to those electolitics (polarized) which have to be changed if are not keeping voltage…
Just few of those F07 does meen really triac scc… more likely are something related to earth leakage or dirty motor connectors or other electronic components from PCB are dead…
I advice anyoneto think from electronic point of viewnot from user…
For ex.: F07 means triac scc.== uC is reading voltage on widing whithout giving commands for opening triac gate… that is happen in tree cases:
1) triac is really SCC
2) leakage to earth of one motor components
3) voltage feedback reading from motor is faulty (ex. 470Kohms resistors)…Changing an electronic component (even triac) is easy using soldering iron… you have to know which one 😉
Re: Indesit WIXL123UK/Y Die’s then starts up again
Bernie wrote:Thanks for the reply Baron.
I get the door lock but not the bit that follows…….make a jump between J4.1 and J4.2 on PCB with J4 connector OUT and let wash program run till end…
what will this tell me?
what do I make a jumper from, which one is the J4 connector?J4 is the wiring connector on PCB which comes from door lock.
Jumper can be done with any wire (in that connector are three wires: two with the same colour/broun and another red, so you have to the jump were goes those with the same colour)…
In this manner you will check if problem came from door lock or it’s wires (in case of running without intrerruption)…Bernie wrote:Also “missing carbon brushes?” do you mean a brushless motor?
BernieYes
Re: WTA / UKW SEPTEMBER 2010 MEETING
Hi All
again the link for booking the room on line is :-
http://www.coventry.hilton.com/ffr
Bryan
Could you check “door lock” contact ( between “L” & “C”) and related wires… for that you can try to make an jump between J4.1 and J4.2 on PCB with J4 connector OUT and let an wash program run till end…
Because is with “/Y” ended, which is for “arcadia” model it could be also missing carbon brushes???
Re: samsung RSH1DBMH
Fan in the evap cover jammed,also move sensor over to suction line on left side.
Bryan
Re: Samsung RS21
Hi MKR
If your at coventry at the meeting i will give you the pointers needed.
Bryan
