Forum Replies Created
-
Posts
-
Re: Hotpoint BFI62 error code
Dave,
Its just constantly blinking on and off with less than a 1 second delay
Re: One for the Comet guys…Proline FF959 Freezer
The last 3 appliances with fault I have been to has turned out to be the PCB,You can check that there is or isnt power coming out from the PCB from the front at the PCB connections.
Bryan :wave:
Re: lg dishwasher
this model has a history of the main wash motor seizing or getting jammed and this will cause a E1 error to be displayed.
Bryan :wave:
Re: creda t/d 37643
what is zbn or jk is that the number on the timer its eaton, the first set of numbers and colours you gave matches with what ive got so i presume it must be the one i need.
Re: lg dishwasher
also the display shoes “1 E” code, water is not supplied ( water tap is not opened) however the water is actually fine
Re: lg dishwasher
recently replaced the board on a LD-14AW 2, the solenoid was tested and found to be ok, the machine fills up but that is as far as it goes. any ideas what to replace/check next?
Re: Bosch dishwasher – need new detergent cpmpartment lid
many thanks for your responses. I can’t see a rating plate around the door – anywhere else I can look before ordering? Thenumbers I gave were from the manual, but it’s loaded with numbers! Cheers.
Re: indesit wd12uk fault code 3 flashes
will check temp sensor as for positioning on new circuit board from what i remember the plugs can only go on in one order cant they?
Re: Flickering display / no ice Whirlpool American FF
You should complain like hell to whirlpool customer care, the original boards were crap and extremely poor in reliability terms. The modified ones (as in the above post) are uncompatable with the originals therefore double your repair costs. All this down to Whirlpool product reliability!!!!!
0870 600 8989 will give you the options to choose Service or customer care… good luck, you’ll need it.
Kevin
Re: control knobs for Teba oven
Can you send me a photo of the knobs that you need as there is numerous different ones.
bryan :wave:
Re: Chemical residue left on plates, cutlery etc.
Hi,
Following your suggestion I removed the spray arms to check them. One of them was partially blocked by what looked like a piece of sweetcorn.
I’ll buy some new detergent next time I’m at the supermarket and let you know how I’m getting on.
Thanks again.
D
Re: Hotpoint Aquarius TDC30s stopped drying
You wouldnt have a part number or reference? i.e is it a full set or a single element type componet?
Thanks
Paul
Re: Hotpoint Aquarius TDC30s stopped drying
Hello again,
I swapped the thermostat and this appeard to fix the heat issue. The only problem was I managed to knock one of the coils (the cardboard bit in the middle bent).
Now two questions :
1) Are these easy to replace or am I going to unchanterd waters for my noob approach.
2) Should the coils glow? now this may sound like a simple question of course but I am assuming this is where the heat comes from?.More for my understanding than anything
Thanks
Paul
Re: Repair, refund or replace?
It was about 25{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} discount plus delivery, however, I don’t think that should mean that it doesn’t work as well as if I bought it retail. I would have paid full price if I’d thought that. 😀
Get your point about rocking the boat. What I’m really worried about is the machine developing more faults once it is out of it’s warranty period though. I’m between a rock (or a lump of concrete) and a hard place. 😆
