Forum Replies Created
-
Posts
-
Re: NEB Vicenza oven Element failure
This was a common problem with this particular product and I believe that they changed supplier of the element.
Oven manufacturer Nardi Italy.
Serviced (I think) by expert appliance care.
Re: Homark oven contact details
The Homark brand was owned by Bernstein Group Holdings based at Westhoughton near Bolton – You could try them.
Ownership of the brand has recently transferred to Premium Appliance brands based in Warrington – Try them next.
These appliances were sold extensively through B+Q, as a last resort, try them.
Re: EuroKera Hob
EuroKera is the glass manufacturer.
Have you followed the instructions correctly?
It maybe a Fagor hob and if you wire them the wrong way then 2 elements won’t work.
Re: SARENA Dishwasher (who makes them?)
Hi there.
The Sarena dishwasher is made by Elco Brandt in France.
It has ‘A’ energy, ‘A’ wash and ‘C’ drying ratings.
Re: Siemens TXL 2402 condenser dryer shows ‘—‘
Hi Martin,
It says:
E-Nr WTXL2402NL/07 FD 8411 200949On the machine itself it says TXL2402.
This is a Dutch machine.Essie
Re: TV630
When you say the microtemp… you mean the round, fuse like sensor ? If so, this is short circuit as seems fine. Providing the element coils are Serv, I presume you do not recommend that the ‘ wing ‘ shaped spade connector is removed from circuit ?
Re: Hoover Performance 1100 washing machine pipe
PLEASE CAN YOU LET ME KNOW HOW TO PLACE AN ORDER FOR THIS PART THANK YOU.
Re: TV630
I must admit that I forgot to check the element itself last night. Where is the Flood Safety Switch located please ❓ I am responsible for another TV630 with a noisy drum problem 😥 and therefore know how difficult it is to get the thing apart – especially the front off (again last night) to get to the ‘ gubbins’ inside to investigate this latest fault further. Please advise. 😯
Re: smeg dwf1 not draining
thanks for that
i now have the front panel removed and have revealed the workings etc
is it a simple job to check the pump for blockages or will i need to call out an engineer in the manchester area if so anyone reccomend a good one.
cheersphil
Re: British Gas Homecare
As a yorkshireman I have to say that what FB has posted sounds like a load of rubbish.
Lets just apply a bit of logic. A take home of 2K a month is easily into the 35K figure when you consider the employers contributions.
The 90 a month bonus start is too low for an operation that has well stock vans and back up second to none. Remember this is multi brand work and if they hit 60{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} 1st time completion they’ll be lucky, 35 completed a week would be a more sensible figure for a call bonus to start at.Sorry FB your post is not an advert for British Gas but a disaster in the efficient running of their business. At your figures they losing money hand over fist on service and what P45 has posted as a reply just BLOWS you away.
Kevin
Re: Whirlpool ADP5966 Fault Code F7
Thats interesting, while I purchased it secondhand 5 months ago the salt compartment is still half full. We use the machine maybe 5 times a week. I will check your suggestion. Thanks, Paul
Re: TV630
On removing the back plate last night, I checked the heater assy fuse with a multimeter and found it fully ‘S’. But I found the male spade connector Open Circuit. There is 231 VAC accross the fuse but on only side of the connector. On removing the connector, it seems this only serves to connect the supply across the element and therefore, providing the element is still intact, believe both leads can be connected together directly without any problems. Any thoughts ?
Re: Philco Manual
Hi everybody,
I lost my washing machine instruction manual (model number: Philco WDN 843 B), and I don’t know how to use it now. Does anyone can send my a soft-copy via e-mail??
my e-mail: minglam@mail.hongkong.com
Thank you very much for your help!!
😀 😀 😀 😀 😀 😀 😀 😀 😀 😀 😀 😀
